Product Description:
1. Description
HS ( V ) Pump is a kind of new generation single-stage double-suction volute centrifugal pump combining with advanced pump manufacturing technology at home and aboard.
2. Purpose
HS ( V ) Pump is mainly applicable to the water feeding of waterworks, power station, industrial water supply, air-condition circulating water, building water supply, irrigation, shipbuilding industry, etc.
Operation Parameter
1. Flux: Q: ≤ 12300 m3/h
2. Lift: H: ≤ 200 m
3. Power: 7.5~2500 kw
- Q:How many square cables does the submersible pump for 7.5KW need?
- According to current I=13A, it is estimated that the cable is less than 10 square meters, so the cable cross section can be calculated at the ampacity of 5A per square meter. The square section of the cable is =13/5=2.6 square. According to the specifications series, optional 2.5 square aluminum cables. When the cable is longer, it is safer to choose 4 square aluminum cables.
- Q:Fire pump control cabinet There are 6 pumps, two indoor fire hydrant pumps, two spray pumps, and two outdoor pumps
- Indoor fire hydrant pump in addition to remote direct Kai, there are modules to start function, that is, on the cabinet to add control module, bus linkage pump, but also fire hydrant button, direct pumping function, a total of three functions.Outdoor fire hydrant pump in addition to remote direct Kai, but also an electric contact pressure meter detection system, water pressure from the pump and high pressure pump stop function.
- Q:What's the difference between a centrifugal pump and a centrifugal pump? What are they used for?
- Centrifuges are generally used to classify liquids of different densities in liquids.
- Q:The suction pump has a nominal suction range of 30 metersHow deep can a well be sucked?Well, sixteen meters,
- Vacuum pump plus form must not reach a standard atmospheric pressure vacuum, so the general can absorb 8 meters is very good, and the self suction pump itself and loss, the horizontal self-priming pump can suck on basic 4~6 meters is very good, self-priming pump. Suction lift of 30 meters is purely in the Mongolian people, does not comply with the laws of nature, obvious anti science.
- Q:Bolus dosage of infusion pumpWhat is the purpose of the pill dose control in the special safety standard for infusion pumps? If the risk is not properly controlled, what is the degree of risk? And how can the open infusion pump be used in this regard?
- (1) the pellet dose in the safety standard of the infusion pump refers to the amount of liquid that is transported to the patient in a short period of time(two) pill dose limit is mainly to control the risk of accidental pill dosage. Especially after the mandatory requirements of pipe blockage in the elastic pipe storage liquid limit amount of agglomeration and the limitation of these methods to release pill dose.
- Q:Water pump does not produce water, what are the reasons?
- 6. is the motor running in correct directions?.7. pump body failure, such as sliding off the leaves or too much gap between the mouth ring.
- Q:Water pump spoon pipe for power plantWhich hero can tell me what is the water pump spoon tube ah? And its role
- By adjusting the amount of oil entering into the hydraulic coupler, the torque of the hydraulic coupler can be controlled
- Q:Fire hydrant pump button, under what circumstances do not need to install?
- There are four things to do:Fire hydrant button to meet the requirements of national standards.In addition to pumping, it can show the location of fire.
- Q:What's the difference between a concrete pump and a concrete pump truck?
- Concrete conveyor pump height and distance can reach hundreds of meters, which is far more than pumping vehicles, but it needs cloth tube, not flexible enough. Less investment.Pump car use more flexible, higher investment.
- Q:Because the water pressure of the booster pump is not enough, it can not work automatically. It can only be operated by hand. It is inconvenient to use.
- The worst case is that the pump is not automatic when it leaves the factory, and no one can say whose product is 100%.But there may be automatic control of this piece, not debugging (this depends on the specific product manual or manufacturer)
1. Manufacturer Overview |
| Location |
|
| Year Established |
|
| Annual Output Value |
|
| Main Markets |
|
| Company Certifications |
|
2. Manufacturer Certificates |
| a) Certification Name |
|
| Range |
|
| Reference |
|
| Validity Period |
|
3. Manufacturer Capability |
| a)Trade Capacity |
|
| Nearest Port |
|
| Export Percentage |
|
| No.of Employees in Trade Department |
|
| Language Spoken: |
|
| b)Factory Information |
|
| Factory Size: |
|
| No. of Production Lines |
|
| Contract Manufacturing |
|
| Product Price Range |
|
