Silicon Bonded Silicon Carbon Alloy Ball - Raw Materials for Refractory
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 20 m.t.
- Supply Capability:
- 1000 m.t./month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
You Might Also Like
Silicon Carbon ball
At present, the iron and steel metallurgy enterprises usually adopt alloying out of the furnace to adjust the steel composition and use the common recarbonizer to adjust its carbon content. When the molten steel is under peroxy state, since the density of recarbonizer is small, it has poor efficiency of adding carbon. On the other side, it can’t sink into the molten steel and there is little possibility of acting with the molten steel, only can act on the top or on surface, so the recovery rate of carbon is low. Nevertheless, many steel enterprises try to resolve the problem by adding carbon cored wire, which increase the production cost and equipment cost, what’s more, it is much difficult t operate.
We has two production lines, the monthly production capacity is 1000 tons.
Specification
C | Si | S | P | H2O | Granules |
20-30% | 45-55% | ≤0.12% | ≤0.2% | ≤0.5% | 20-50mm |
- Q: Are fire materials poisonous after burning?
- Neutral refractory is mainly composed of alumina, chromium oxide or carbon. Corundum products containing more than 95% of alumina are a kind of high quality refractory materials with a wide range of uses. Chrome brick with chromium oxide as its main component has good corrosion resistance, but its thermal shock resistance is poor, and its deformation temperature is lower at high temperature. Carbon refractories with carbon bricks, graphite and silicon carbide products, low coefficient of thermal expansion, high thermal conductivity, good thermal shock resistance, high strength, resistance to acid and salt corrosion, especially weak acid has good resistance, without wetting of the metal and slag, light. It is widely used as lining material of high temperature, and also used as lining of autoclave in petroleum and chemical industry.
- Q: What is the difference in the nature between the refractory material and thermal?insulation?material
- thermal?insulation?material is used to thermal insulation and the transfer of heat insulation. refractory material is defined as greater than 1580 ° non-metallic materials, such as calcium silicate board. its using temperature can reach to 1100 degrees, and some can also be used at high temperatures, and all high-temperature industrial can't be oprated without it, and the using temperature of polycrystalline alumina fibers can reach to 1800 degrees
- Q: What are the standards of refractory concrete ?
- The special concrete compound by uitable binding materials, refractory aggregates, admixtures and water at a certain ratio. It can maintain the desired mechanical property at high temperature of above 900 ℃ for a long time. The property depends on the material and matching of all the aggregates, admixtures and binding materials. Its material, composition and ingredients are similar to these of refractory castable. Refractory aggregate can be dry slag, broken refractory bricks, basalt, bauxite, magnesite, etc. According to the binding material, it can be divided into Portland cement refractory concrete, aluminate cement refractory concrete, sodium silicate refractory concrete, phosphate refractory concrete, magnesia refractory concrete, etc. (8) The particle material and powder material in refractory concrete are called aggregate and admixture respectively. The mixture of concrete can be moulded by casting, vibrating or ramming. And proper measures to promote their hardening can be used in accordance with the hardening characteristics of the binding materials (such as air hardening, water hydraulicity, thermal hardness, etc.). It is mainly used to build the monolithic lining of industrial furnace and procast blocks. Of all the concrete, the ones used for under 900 ℃ is called heat-resistant concrete, and they are used for the foundation and chimneys, etc. of industrial furnaces and thermal equipment.
- Q: Urgently!! Refractory problems, online, etc.
- The service life of most refractory materials is a pair of contradictory effects. As a result, one aspect of the contradiction is porosity, and the other is volume density. The larger the volume density is, the smaller the porosity is and the more erosion resistant, but the thermal shock effect is very poor. The bigger the porosity is, the smaller the volume density is, the better the thermal shock effect is, but it is not resistant to erosion. More professionally, two curves should be made to find the intersection of the curves to adjust the recipe and production process
- Q: What are the structural properties of refractory materials provided by the manufacturer of the refractories include?
- On the other hand, the turbulence is severe, and the side wall of the tundish is washed into the liquid steel and the service life of the lining of the tundish is reduced. In order to solve this problem, China 5%% honing develops a tundish anti turbulence pad, which is made of Al2O3>75% high alumina castable. Anti turbulence pad mounted casting ladle and tundish flow impact zone in the bottom of the flow out of the steel ladle nozzle casting hole center back in the anti turbulence pad repeatedly to consume the kinetic energy of the fluid flow, thereby reducing the steel flow speed, avoiding turbulence.
- Q: How long is the duration of fire resistance that fireproof door of level B can endure?
- The national standard for fireproof door of level B is 1.5h, which must be achieved. The data GB12955-2008 means that the door leaf of raw material is 0.8mm-1.2mm in thickness and door frame is 1.2mm-1.5mm in thickness. And other metal melting temperature shall not be less than 950℃, the duration of fire resistance shall not be less than 0.9 hours. Fire department will check and accept based on the manufacturer's inspection report, so you have to refer to manufacturer's inspection report if you want to know more in detail.
- Q: whether the aluminum silicate thermal insulation material is fireproof or not?
- aluminum silicate is fireproof, and the melting point is between -40 ~ 800 ℃. Aluminum: it takes the flint clay clinker as raw material, produced by resistance or electric arc furnace fusion and injection fiber-forming process. its characteristics: Low thermal conductivity, excellent thermal and chemical stability, without binder and corrosive material.
- Q: What refractories can withstand high temperature above 2100 degrees?
- It depends on refractoriness of refractory materials. The three refractory bricks above is 300 degrees higher than quartz sand in refractoriness. Magnesia brick: Cast corundum brick with greater than 2000 degrees refractoriness should be enough for you to use. But products like quartz sand merely keeps 1600 to 1700 in refractoriness generally. As you described that refractoriness is greater than 1990 degrees, it is feasible to use hearth made by mixing of quartz sand and refractory cement, which can work for some time at 200 degrees. It is also ok to use dolomite brick whose refractoriness is greater than 2000 degrees.
- Q: What are the requirements for fire?rating of construction suspended ceiling material ?
- In fireproof design of all parts in interior decoration, fireproof design of suspended ceiling is the most important. Because the flame is burning up in fire and the suspended ceiling is the first and most direct part to test fire; at the same time, it has a direct impact on the evacuation. Therefore, in indoor suspended ceiling decoration design, fireproof work should be considered fully. Code of fire prevention design of interior decoratio of buildings has detailed provisions for fireproof?performance of indoor suspended ceiling materiial of different civil buildings. Suspended ceiling (sprung roof) refers to the top decoration of a house. Suspended ceiling, an important sub-project in construction decoration project, and the hidden layer of electrical equipment, ventilation and air condition, communication and fireproof, alarm pipelines, etc. has the functions of thermal insulation, sound insulation and absorption. Suspended ceiling plays an important role on the entire house decoration. Proper decoration to the house top surface, can not only beautify indoor environment, but also create a colorful interior artistic image. When choosing decoration materials and design of suspended ceiling, you should follow the principle of saving material, being solid, safe, beautiful and practical.
- Q: What are the refractories for converter?
- Magnesia carbon material with large surface repair vessel, in addition to supporting the use of magnesia and magnesia cement.
Send your message to us
Silicon Bonded Silicon Carbon Alloy Ball - Raw Materials for Refractory
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 20 m.t.
- Supply Capability:
- 1000 m.t./month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
Similar products
Hot products
Hot Searches
Related keywords
