PVC Pipe SDR21

Chat Online

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

pvc pipe
Water supply pvc pipe
Water discharge pvc pipe
Plastic PN10 and PN16 pvc pipe
DIN8077, DIN8078, ISO 15874 pvc pipe

Our pipes and fittings can be made according and conforming to the following International Standards:

1) American standard (ASTM Sch 40 & Sch 80, SDR 21, SDR 26, SDR41)

2) British standard (BS 3505, BS 5255, 4515)

3) Singaporean standard (SS 141, SS 272, SS 213)

4) Australian standard (AS 1477, AS 1415)

5) National standard (GB 10002, GB 5836, GB 14823, GB 13664)

6) International standard (ISO 4422, ISO 3633, IEC 614, GY 3050)

PVC Pipe Features

Non-conductive: Good insulation, assuring a safe system
Smooth surface: Small friction coefficient to ensure the cables go through smoothly
Fire resistance: Self-extinguishing, do not support combustion
Corrosion Resistance: Resistant to acids, bases and salts, assuring a lower maintenance cost and a longer performance life
Impact strength: Resistant to compression and impact, suitable to be buried in concrete
Easy Installation: solvent cement and threading joining
Usage:Electric wires installation, Supply water, Irragation Water, Drainage

Q:I'm would like to buy this in store and not online. Please let me know of where you think this item might be available for purchase.Thanks: try united states plastic corp.

Q:The iron pipes and plastic pipes, that antifreeze: If the plastic tube is not water minus 30 degrees is also fine, there is water 3-5 degrees below zero on the cracking of the. The iron pipes are much more affordable.

Q:I have a hole ins a plastic tube that contains water how do I seal the hole?: You may find that you could A: use a water bed repair patch and than wrap tightly with duct tape or B: get a tube of some silicone like they use to repair aquariums. apply liberally and than wrap with plumbers tape. Let it dry as good as possible before putting any real force to it. Good Luck!

Q:Is the PVC tube a plastic tube or a plastic tube?: The vinyl chloride homopolymer and vinyl chloride copolymer are collectively referred to as vinyl chloride resins. The material is a non crystalline material. PVC materials often use stabilizers, lubricants, auxiliary processing agents, pigments, anti shock agents and other additives in practical use.

Q:Our Kenmore washing machine #110.2970091 recently started leaking water from underneath. When we looked, there was a clear plastic bag/tube attached to a hole on the side of the tub that was leaking.The tube was taped up at the bottom and doesn't look like it's supposed to be there, the water in it looked like it was there awhile. We bought this used so it doesn't have a manual or warranty. If it is an overflow pipe, where is the excess water supposed to go? We have it hooked up to the laundry sink.Thanks: I would plug it. It is probably an overflow drain. If the washer gets too full it will probably not get the floor any wetter than if the overflow drain runs on the floor. If this happens open the tube up and run it into a pan.

Q:My girlfriend got me a roll of the new 2009 pennies. I'm curious to actually look at them, but I'm worried that if I break open the roll, that will decrease the value of them. If I opened the roll and put the pennies in a tube (assuming I don't get fingerprints on them), will they be worth less than if I just keep them in the original paper roll?: it depends if the paper wrapper is a special mint one or just a bank one. if a special wrapper it is best to keep it in it. The mint is selling the rolls with a special wrapper. However paper is not good for coins for most wrappers are cheaply made and have acids in the paper. A hard plastic coin tube is the best for it is archival to an extent, for air still can get in there. A pair of white cotton coin gloves stops the finger prints on the coins problem. A soft clean handkerchief that has no fabric softener on it works well also, but one needs to be more careful. hope this helps.

Q:What are the disadvantages of using plastic tubes compared to other materials?: One of the disadvantages of using plastic tubes compared to other materials is their susceptibility to wear and tear. Plastic tubes are more prone to cracking, breaking, or deforming over time, especially when exposed to extreme temperatures or pressure. Additionally, plastic tubes may not be as durable as other materials, such as metal or glass, which can impact their longevity and reliability. Moreover, plastic tubes may not offer the same level of chemical resistance as other materials, making them unsuitable for certain applications where corrosive substances are involved.

Q:Pex Tubing: Generally barb fittings are determined by the inside diameter of the tubing. Cut a small piece and take it to the hardware store to match it up,or measure the inside diameter.There are two types of barb fittings.One is used with a hose clamp to secure it. The other has a plastic ring where the tubing attaches and requires no clamp. If you are attaching PEX tubing you should use a hose clamp to secure it as it is not as plyable as standard plastic tubing.Be careful not to over tighten the clamp.

Q:a. ultraviolet (germicidal light)b. 121 C at 15 psi for 15 minutesc. 160 C for 2 hoursd. all are correct: If it were a Glass tube the answer would be A. UV Light does not go through glass well and would not kill much. If it is a plastic tube, D.

Q:I don't want an online store.please and thanks!!: Best place is a hobby shop. People use them for everything from holding dice to keeping change in.

3. Manufacturer Capability
a)Trade Capacity
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range