Q:Development of pneumatic components，The expansion of application of pneumatic technology is the development of pneumatic industry

A smaller, lighter weight and lower power consumption. In electronics, pharmaceuticals and other manufacturing industries, the processing volume is very small, it will limit the size of pneumatic components, miniaturization, light is the first development direction of pneumaticcomponents. An ultra small solenoid valve with a thumb size and an effective cross sectional area of 0.2mm2 has been developed abroad. It is more ideal to develop components with smaller size and larger flow. To this end, the same size of the valve, the flow has increased 2~3.3 times. There is a series of small solenoid valve, its body width is only 10mm, the effective area of up to 5mm2; wide 15mm, effective area of 10mm2.Electromagnetic valve power consumption abroad has reached 0.5W, will be further reduced to adapt to the combination of microelectronics.The gas source treatment assembly mostly adopts the block type block structure at home and abroad, which is not only compact in size, but also convenient in combination and maintenance.The positioning accuracy of the actuator is increased, the rigidity is increased, the piston rod is not turned, and the use is more convenient. In order to improve the positioning accuracy of the cylinder, the application of the cylinder with the brake mechanism and the servo system is becoming more and more common. The cylinder with servo system can still get the positioning accuracy of + 0.1mm even if the supply pressure and the load change.

Q:It is a standard pneumatic drive element. What functions does it have on the cylinder?

Two 、 wear rule of cylinder and its reason(1) the wear rule of cylinderFrom the longitudinal section of the cylinder (along the axis of the cylinder): irregular, tapered, or tapered". The maximum wear parts: cylinder with the piston at TDC on the first piston ring corresponding to the upper reach of the piston ring wear, cylinder order form "". Under special circumstances, the location of the maximum cylinder wear in the middle (drum). On the same engine, the wear of different cylinders is different. The wear of the front wall of the first cylinder and the back wall of the last cylinder of the water cooled engine is more serious.From the cross section of the cylinder: uneven wear, wear irregular oval. Each cylinder along the circumferential direction of the maximum wear parts: general is the intake valve near the wall opposite the maximum wear.

Q:Where are the industry standards for pneumatic components?

5, GB/T, 2350 - 1980 (1997) hydraulic, pneumatic systems and components, piston rod, thread type and dimension seriesEQV ISO 4395:19786, GB/T 2351 - 2005 hydraulic pneumatic system with hard tube outer diameter and hose inner diameterISO, 4397:1993, IDT7, GB/T, 3452.1--2005 hydraulic pneumatic O rubber sealing ring first parts: size series and toleranceISO, 3601-1:2002, MOD

Q:I used the ACE 2013 edition, how can I call the components of the library pneumatic components and hydraulic components, ah, how can I not call ah?. Thank you！

A storage unit in which the PLC software element corresponds to the memory of a computer. The status of the soft components can be directly queried in the same PLC.

Q:Pneumatic oil filter oil in what

Oil mist cup lubricating oil level height can not exceed the total height of the 3/4 cup, oil: turbine oil No. 1 (International designation: ISO VG32), its properties are very thin viscosity of 7E degrees (the equivalent of lubricating oil, sewing machine oil 5E ~7E degrees); GB grade: 7 machine the lubricating oil (viscosity 7E degrees), sewing machine oil, is also more convenient choice.

Q:What are the components of a cylinder in a pneumatic system?

In pneumatic systems, the cylinder belongs to the actuating element

Q:What are the similarities and differences between the pneumatic directional control valve and the hydraulic directional control valve?

The requirements for leakage are differentThe hydraulic valve is strict with the outward leakage, but a small leak inside the component is permissible. For pneumatic control valves, in addition to the clearance seal valve, in principle, does not allow internal leakage. The internal leakage of pneumatic valves causes the risk of accidents. For pneumatic pipes, a little leakage is allowed, and the leakage of the hydraulic pipe will cause pressure drop and pollution to the environment.

Q:Which is good between pneumatic tools and power tools?

The use of pneumatic tools:1., the air is easy to obtain, and the work pressure is low, the used air can be discharged locally, without the need to recover the pipeline2. gas viscosity is small, flow resistance loss is small, easy to central gas supply and long-distance transportation3. pneumatic actuator, high movement speed

Q:Pneumatic components of SMC pneumatic components

An element of a pneumatic element that does work by the pressure of the gas or by the force of its expansion is the component of the elastic energy of the compressed air that is converted to kinetic energy. Such as cylinders, pneumatic motors, steam engines, etc.. Pneumatic component is a kind of power transmission method. It is also an energy conversion device and uses gas pressure to transfer energy. 1. The layout of pneumatic equipment is simple and convenient, and the equipment protection is simple. Medium for air, compared to the hydraulic medium is not easy to burn, so the use of safety.2, the operating medium is inexhaustible air, the air itself does not cost money. The exhaust disposal is simple, without polluting the environment and low cost.3, the output power and operation speed adjustment is very simple. The speed of the cylinder is usually less than 1M/S, faster than the hydraulic and electrical methods of action.4, high reliability, long using life expectancy. The number of useful measures of electrical components is about a million times, and usually the solenoid valve life is greater than 30 million times, some good quality valves beyond 200 million times.

Q:Pneumatic components, those equipment needs to be used, specific points. Additional reward

It must be the executing agency. If you want to do such sales, you can run automated equipment, automated assembly line manufacturers, such companies, pneumatic components should be used more!!