Monocrystalline 195W PV Solar Panel Solar Module

Ref Price:
Loading Port:
shanghai
Payment Terms:
TT or LC
Min Order Qty:
-
Supply Capability:
10000000 watt/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Description: 

Solar modules use light energy (photons) from the sun to generate electricity through the photovoltaic effect.

The majority of modules use wafer-based crystalline silicon cells or thin-film cells based on cadmium telluride or silicon.

The structural (load carrying) member of a module can either be the top layer or the back layer.

Cells must also be protected from mechanical damage and moisture. Most solar modules are rigid, but semi-flexible ones are available,

based on thin-film cells. These early solar modules were first used in space in 1958.

CNBM Solar photovoltaic (PV) Panel is designed for large electrical power requirements.

It is the optimal choice for both on-grid and off-grid power systems.

 CNBM Solar panel offers high performance of power per square foot of solar array.

Monocrystalline silicon(c-Si): often made using the Czochralski process. Single-crystal wafer cells tend to be expensive,

 and because they are cut from cylindrical ingots, do not completely cover a square solar cell module without a substantial waste of refined silicon.

Hence most c-Si panels have uncovered gaps at the four corners of the cells.

Characteristics of Solar Monocrystalline

I. Solar Cell : High efficiency crystalline solar cell.

Even if under the weak light, the solar module can produce maximum power output.

II. Tempered glass (toughened glass): Anti-reflecting coating and high transmission rate glass increase

 the power output and mechanical strength of solar module.

III. EVA and TPT: Using high quality EVA and TPT to prevent destroying and water.

IV. AI frame: Without screw, corner connection. 6 holes on the frame can be installed easily.

V. Junction box: Multi function junction box with water proof.

VI. Long lifetime: ≥25 years; Less power decrease.

VII. Good performance of preventing from atrocious weather such as wind and hails.

VIII. Resisting moisture and etching effectively, not effected by geology.

IX. The certificate issued by international authority: UL, TUV, IEC, VDE, CE.

 

vantages of Solar Monocrystalline

• CNBM Solar performance guarantees for 25 years

• 10 years guarantee for workmanship

• Timeliness of delivery

CNBM International Corporation's products including Monocrystalline Solar Panel,

 Polycrystalline Solar Panel have received and enjoyed famous reputation in many countries and

regions in the world .As a solar panel manufacturer in China, we strive to provide our customers with excellent service,

superior products and unmatched value.  

Specifications:

 

MONO

190W

195W

200W

Nominal peak power(Pmax)

190Wp

195Wp

200Wp

Maximum power voltage(Vmp)

36.7V

37.0V

37.4V

Maximum power current(Imp)

5.19A

5.27A

5.35A

Short-circuit current(Isc)

5.56A

5.63A

5.68A

Open circuit voltage(Voc)

44.8V

45.2V

45.5V

Optimized cell efficiency(η)

17.60%

18.20%

18.60%

Power tolerance: ±3%

Limits

Operating temperature               

-40°C to +85°C

Maximum system voltage               

1000VDC

Temperature and Coefficients

NOCT

48°C±2°C

Number of cells and type of connection

72,serial connection

Dimensions

Length:1580mm
Width:808mm
Height:35mm

Net weight

14.80kgs/pc

Gross weight

450kgs/ctn(28pcs/ctn) 33kgs/ctn(2pcs/ctn)

Package dimension

1635x1140x956mm   1598x838x88mm

Container loading

868PCS/40’GP   62PCS/PALLET
372PCS/20’GP   62PCS/PALLET

STC: Irradiance of 1000W /m2, Air Mass of 1.5, Cell Temperature of 25°C

Guaranteed Power Output
   Warranted Tolerance: ±5%

15 year:90% of its nominal power rating

25 year:80% of its nominal power rating

Impact Resistance

Can bear the force that is generated by one 227g

steel ball fall down from 1m height

Warranty period

10 years:Materials and workmanship defects

Certificates

CE,ISO,IEC61215&61730(TUV),UL1703/CSA,MCS

Cells

Monocrystalline silicon photovoltaic cell

Monocrystalline 195W  PV Solar Panel Solar Module

 

FAQ:

1. How long will my inquiry get response?

 Your inquiry related to our products or prices will be replied within 24 hours. 

2. Can I get professional service and suggestion?

Well-trained and experienced staffs to answer all your questions in fluent English. 

3. Do you accept OEM or customized design?

OEM & ODM, any your customized lightings we can help you to design and put into product.

4. What if I need specific design?

Distributorship are offered for your unique design and some our current models.

 

 

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:why aren't solar panels for your house more affordable?
You okorder.com (or any other website you can find in a search engine) to get a list in your area. Good luck!
Q:Can I build my own Hot Water Solar Panels?
I worked for a plumbing service that offered hot water solar panel installs and replacements. I've replaced perfectly good solar panels for people who wanted to upgrade to the latest. We had piles and piles of panels out behind the shop. We use to scrap the copper and sell the glass panes. A few people would ask to scavenge panels and the boss would let them have it cheap, just to move some of the stuff. I would do the same. I'd find a local installer and see what they do with the leftovers. Chances are, if you searched diligently, you could probably find panels in good shape and use them to supplement your energy usage. Bear in mind, solar hot water system are very different from standard systems. They usually have a much larger storage tank. Typically 80-20 gallons compared to 40. They have a circulating pump and temperature sensors to move the heated water from the panel into the tank. These larger hot water heaters/tanks have much better storage and insulation to keep the water temperature that is generated during the day to last into the evening when people are home to use the shower and wash clothes to take advantage of solar heat. It's not just a matter of getting a panel and slapping it up. There's are technical aspects that need to be followed and if you don't know them, I would advise against doing it yourself. Study up on it and see if it's something you want to tackle on your own before you go too far doing legwork to find out details that might be cost prohibitive or too complicated. Good luck.
Q:Solar Panel for a Science Project? Lamp as Light Source? How will this work?
Q:Why are solar panels only 0% efficient?
Mainly due to reflection (micro-structuring of the surface helps here), incorrect wavelength of the light (the panel is only sensitive to a certain wavelength range) and heating of the panel (due to the incident light/thermal radiation). The remainder is either reflected or absorbed by the cell and re-emitted as heat. Absorption by e.g. the glass panel is slight (a few %), as is absorption/reflection by the necessary surface contacts (again, a few %). Higher efficiency is possible, but brings its own drawbacks (like higher cost). You could now go into two directions: - high efficiency cells/panels with (likely) higher cost and complexity for mounting (like lens or mirror based systems, aka concentrator systems, that increase the light level on the cells in order to increase efficiency) - low cost systems (cheap as dirt) that will allow you to cover every surface of a building, efficiency is less important if you can compensate by a much larger covered area As to the efficiency limit: there is a theoretical limit (from thermodynamics - don't ask me how or why) in the range of 30...40%, depending on which publication you want to believe in.
Q:How Can I Reduce A Solar Panels Output To 3volts From 9volts?
Build okorder.com/
Q:How are solar panels developed and distributed in America?
The first link below is one of the best sites for recent news about solar panels. You should be able to find stories about solar panels under development today. A little bit of the history: Solar panels have been around for about 50 years now. They were first used to power spacecraft. Solar power for domestic use started to develop rapidly in the 970's during the first oil crisis, but as energy prices fell in the 980's solar development slowed. Most of the large solar panel makers were purchased by large oil companies who seemed not to be too interested in solar. In the late 990's as concerns about both Peak Oil and Global Warming grew there was renewed interest in solar power and a number of new companies were started to develop new kinds of solar panels. Many of these new companies have grown larger than the older solar companies still owned by big oil companies. Over the last 7 years or so growth in the solar market has been explosive with a compound growth rate of almost 40% per year. In 2005 the solar industry for the first time started to consume more silicon than all other electronic industries combined resulting in a world wide silicon shortage that is still with use. New silicon refineries are coming on line and the shortage is expected to diminish by 2008 or 2009. Check out the two links below. They will help you a lot.
Q:so what do you all think about solar panels? are they worth it?
Current commercially available photovotaic panels are about 5% efficient. The current record in the laboratory is 42.8%. There are designs expected to achieve 65% on the drawing board. It's like investing in low interest rate bonds. If you just wait a couple of years and then invest, you will make more money simply because you would then have higher interest rates. Likewise with solar panels, if you just wait a few years then because they will be so much more efficient, you'll get a better return over the life of the panels.
Q:Question about using solar panels......?
I don't think it is enough solar power. Your motor requires .5A x 9V = 3.5 watts. The solar cells are .450A x 4V x 2ea. = 3.6 watts, .2A x .5V = .3 watts, .A x 9V = .9 watts total solar = 4.8 watts. The problem with connecting the cells in series to get the right voltage, like the two 4V cells in series with the .5 volt cell (total 9.5 volts) is that the .5 volt cell limits the maximum current to only 0.2A. If you paralleled that with the 9V cell, you would get 9 volts at 0.2 + 0. = 0.3A, too low to operate the motor at its design current and voltage. The best you could do is put the two 4V cells in series, and in parallel with the 9V cell (a blocking diode might be a good idea, but probably not required for such a small array). That way you get 8 volts at 0.55 amps.
Q:should i get a solar panel?
Solar panel is one of the best sources nowadays to generate electric energy using the sun rays that comes from the sun. But, this set can be so hard to find and it’s very expensive to buy.
Q:What are solar panels made of?
Well i am not sure but to my knowledge all i know is that the purpose is to save solar cells which are later created into energy Solar energy is generated from solar panels. Solar panels are slabs of semi-conductor metal. Technically speaking, they are a slab of silicon semi-conductor doped or added with impurities to make it a better conductor. Solar panels could also be made of Gallium Arsenide which is a semi-conductor metal exclusively used in photo-voltaic cells. The silicon slabs are polished and glossed before doping. After processing, for protection, a thin glass layer is embossed on the solar cells slab. Silicon also is shiny and reflects about 35% of sunlight. Hence, an anti-reflective coating is usually applied over the slabs to reduce the amount of sunlight lost. Amorphous silicon solar panels are different from the traditional ones made from silicon slabs. Amorphous silicon solar cells are thinner and more efficient that the silicon ones and also the materials cost of this variety is far lesser than the traditional. Amorphous silicon slabs are developed with superior processes which makes them less susceptible to breakage during transportation. This makes them a more viable investment when it comes to buying solar panels.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range