Hot Item! Antique Plated Faucet

Ref Price:
$45.83 / pcs
Loading Port:
Payment Terms:
Min Order Qty:
50 Sets PCS
Supply Capability:
2000Sets Per Month PCS/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Product Name:Antique Plated Faucet
Carton Packing Size:45*43*44.5cm
About product:
1.Two handles faucet.
2.Easy to installation and eas to clean.
3.High in quality and low in price.

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Sink Faucet Rubber Seal needs replacing?
You can get the ring from any hardware store. However I recommend you just buy a variety pack with 10-20 different sizes. That will save you many trips back to the hardware store if one doesn't fit. Also check with friends to see if anyone has a couple of pipe wrenches you can borrow.
Q:how do i change the stem and seat in bathtub faucet?
Paul gave the good answers . But , a leaky faucet may only need a new rubber washer on the end if the stem. when you have the stem removed you and feel the seat in the faucet with your finger and feel if it rough or it is smooth. or if it has a crack or notch worn in it. if it is nice and smooth , you prob dont have to replace it unless you just want to. the cheapest way to rebuild your tub faucets is to go to home depot and buy a " remodelers tub faucet kit " for about $40 you get all 3 stems and seats , and 3 new shiny knobs and maybe the tool too. that is what i did . and replaced all 3 stems and seats like you want to do. or you can pay $10 for just one stem. just remember to ask for the remodelers tub kit. google " remodelers tub kit " and you will see what i am talking about. you might need to buy the seat removal tool. extra be sure to take your old stems with you so you can compare them and get the correct ones.
Q:hot water faucet in bathtub makes thump noise and stops running?
Is it possible that part of the old rubber washer is still in the faucet? I had something similar happen to me once. The culprit turned out to be a valve. Someone had installed a basin shutoff (the little ones with the oval handles) as an isolation valve on the water heater (I rent). The rubber seal inside had torn loose and would intermittently stop the flow of my hot water. Drove me absolutely bonkers until I found it. G'luck!
Q:The basin of the basin of hot water pipe is broken, how to replace
Water hose damage, just replace the hose, close the hot water angle valve, with a wrench counterclockwise to loosen the hose connection angle valve hot water pipe hex nut, counterclockwise hose rotation, release hose and faucet The connection thread of the nozzle. If the time is longer, the thread rust, it may be difficult to twist, you can put the hose 90 degrees and then pull. Holding the old pipe to the plumbing store, buy a hot water pipe to re-install it. Note that the end of the hose connection faucet has a long, short head difference. The other end is G1 / 2 of the joints, generic.
Q:New to buy the faucet and bathroom basin does not match, feel some water leakage how to do?
It is best to replace the unified brand model leader, so that the product of the match and the whole will not be a problem
Q:bathroom faucet is leaking, how can i solve the problem? pic is attached, come and help, thanks!?
If your faucet is leaking out the spigot you're working on the wrong part of the unit. This is a tightening hold down nut that threads up onto the water feed pipe and is most likely corroded or rusted in place so bad that the only way to get it off will be to crack it with a cold chisel and twist it off, or get a Dremel tool with a cutter wheel on it and cut it off that way. Either way, wear safety glasses while removing it as rust particles in the eyeballs are not fun. If the leak was coming from underneath the sink, under the faucet, then yes, you'll need to replace the entire fixture. If you do, when you put it back together and put the new nuts on where this one comes off, put a little vaseline on the threads before you put the nut on, it will make it go on easier and certainly, if you ever have to do this again, it will come off easier.
Q:What are the models of faucet specifications? How to identify the faucet is good or bad?
The standard washbasin's mouthpiece is the M24 specification. The faucet of the dish is M22, and the connector is not the same. Non-standard products on the free.
Q:I am getting pebbles clogging up the cold water side of my bathroom faucet, whats up with that?
If you have just had work done on the plumbing, you could be seeing sediment from the interior of the pipes that was dislodged during the work. I find it odd that you are seeing this only on the cold water side (assuming you mean you don't have a mixer, but separate taps?). Don't install a water softener, as softened water is very bad for you, your children, you pets, and your plants. See what a plumber has to say about it.
Q:What brand of basin is good?
I use the eagle bathroom, aftermarket is better, you can help repair
Q:Taiwan basin with a single hole is good or three holes of the good, what are the advantages and disadvantages
Must not, three holes of the small aperture, single hole aperture.
We are very popular with consummate skill, advanced workmanship, perfect after sales service in the world. From now on, our company devotes ourselves to enterprise construction and development, market is the guide, management is the basis, science is power.

1. Manufacturer Overview

Location Kaiping,Guangdong
Year Established 2004
Annual Output Value Above RMB5 Million
Main Markets
Europe and the United States, Australia

Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port Guangzhou
Export Percentage
No.of Employees in Trade Department 4 People
Language Spoken: English;Chinese;
b)Factory Information  
Factory Size: Above 3000 square meters
No. of Production Lines 2
Contract Manufacturing OEM Service Offered;Design Service Offered
Product Price Range Average