Q:Double hole basin faucet how to install, what tools?

Double hole is mainly for hot and cold water mixed with water, no hot water, just take a cold water pipe. The other who is blocking it.

Q:Open the faucet, the faucet and basin connection seepage, while the basin is also leaking under the water, leading off on nothing, what parts are broken? Thank you!

The faucet is broken, it may be on the faucet when the seal tape or gasket seal caused by lax, may also be broken.

Q:Wash basin faucet how to change the hose

First, remove the whole copper fixed base. Second, the nut from the threaded tube counterclockwise rotation down. Three, hose worn yellow wrench, nut, thread tube, silicone pad. Four, between the hose through the need to install the vessel (sink, basin, etc.). Note: the silicone pad in the vessel on both sides of the installation of a piece, and finally tighten the fixation can be more stable. 5, the hose of the small head, hand screw into the faucet, screwed to the screw can not move, without the help of other tools to die.

Q:Faucet with the basin of the screw how to take, no position wrench no place to put, hand and twist fixed

Go to the hardware store to buy socket wrench!

Q:i try to fix it myself.i can't seem to unscrew that white plastic ring, it was really tight. so what should i do now? should i hire a professional?

did u try using pair of large pliers? are u puttin in new one? where wuz leakin at..at hose or drippin..did u check gasket on both ends? no.u dont need to hire a professional. still cant get it off,,break it off or cut it..if putting new one in..new one comes with new plastic ring..are u sure u are turning it counterclockwise? big pair of channel locks seem to work the best.if that dont work..take a screwdriver and break it outta there.lots of luck

Q:American Standard 3-hole double basin basin faucet how to install

Outlet: the length of 121 mm "C" type outlet, handle: the word ceramic handle, faucet body: cast copper body, spool: ceramic spool, bubbler: √, water components: metal pull drainage group, Mounting components: fasteners, screws, plugs, gaskets

Q:The sink fixture when installed never sealed properly and water can seep between the portion of the faucet that meets the sink basin. Just a small area - I'm not replacing the sink - just can't and won't. I had used some clear caulk around the base of the faucet fixture, but it came off after a few months: it was silicone, but in the fine print it says that it was for windows and doors (I just took the tube he handed me then left). It worked fine while it lasted, but what type would you suggest?

Whatever you use you have to get the sink up so you can fill the space under it. You can't just fill the crack because it won't seep in where it can get a grip.

Q:hey guys, im replacing a kitchen faucet for my mom right now, and Its not one of the ones where it scres in on the two side panels, it has a long threaded neck that attatches to the sink basin, how would I take this out, I tried spinning the faucet to just unscrew the threading but it pivots...

Faucets that I'm familiar with sit on top of the sink and are bolted down below the sink. You have to loosen nuts under the sink from the threaded water supply lines on the bottom of the faucet unit, then lift the entire unit out from the sink. That leaves holes in the sink. Threaded water supply lines on the bottom of the faucet fit through those holes and water lines from your house's water supply are attached to those. But the handles, neck, the whole shooting match is one unit.

Q:How to connect the water heater to the basin

Before the renovation, you need to do a good job between the wash basin and the water heater.

Q:Toilet double hole basin is the number of holes

You ask this question, is certainly the use of hot and cold faucet, you are worried about the purchase of double-hole hot and cold faucet hole and the basin hole is not complete, not installed it