Q:i have two problems.1. water is leaking out from the cold faucet. I unscrewed the plastic cover, it looks fine, but i can see the water coming out from the iron thing. I suppose the only solution is the replace the whole thing? but the whole thing seems to be glued to the sink. 2. water is dripping down under the sink around this twisted plastic tube. ( i don't know the proper name for those things.) i can see mineral kind of things accumulating around one black plastic circle kind of thing. i think that this should be an easy fix, what should I buy? should just buy that one thing or replace the whole plastice tube, etc?thanks.

Unless this faucet is near and dear to your heart, just replace it. Be sure to replace it with a good one, because the cheap plastic ones only seem to last two or three years. Your faucet isn't glued to the countertop, it's just attached via two or three plastic nuts. You have to get directly below the faucet (where the water connections are) and you should see what you need to remove to get the old faucet off. There is a special wrench called a basin wrench that you can use or you can just use some pliers. They can be very tight and hard to remove though since you won't have much room. Be sure you turn the water off before you do any work....

Q:I want to change the faucet of the wash basin, ask the steps. There are pictures

Under the basin corresponding to the leading parts, there are two screws, the screw loose, the faucet can be too high.

Q:I have a Kohler (sp) faucet in my master bath that's come loose. I've looked underneath for some kind of bolt to tight, but I don't see anything there to tighten. I'm wondering if it was fitted badly and the means to tighten it lays between the plywood and the granite top. Thoughts?

Because you'll NEVER get a standard wrench up in there (I've tried, trust me), you'll have to pick up a cheap basin wrench at your local hardware store. See below link for pic.

Q:Kitchen pots and faucets with what material is good

Faucet is good or bad mainly look at the core material, pure copper core is the best, followed by stainless steel, the appearance of the best material is stainless steel or galvanized. More durable and on the grade.

Q:What is the use of the hole below the basin faucet, on the basin

You say is the double-hole faucet wash the face of it, a total of three, that is the middle of some double-hole faucet will highlight some of the middle, so stay

Q:American Standard 3-hole double basin basin faucet how to install

General is the standard of this faucet is the case

Q:The faucet is to buy a washbasin when the package, the beginning of the water quite big, with more than six months of water is very small, very fine point. Do not know is the water dragon

There is something inside the faucet, open to clean up!

Q:A few days ago to the home of the kitchen faucet for a new, but after the change of the problem came, in the faucet and pots connected after the discovery of the tap base and pots connected is not strong, always able to turn, and later found The bottom of the fixed nut is loose, you want to tighten some of the metal gasket are squeezed and can not be fixed (metal gasket is a single hole screw).

In the middle of the two studs with a few large nuts on the tightened

Q:I've recently seen two movies where they show a sink with two faucets. One on each end of the basin. I'd never seen such a thing. Is one hot and one cold or what? Isn't that a little inconvenient if you want warm?

problematic to permit you realize through fact there are this way of huge volume of diverse variety stems yet here is going. First close the water off the two below the sink or on the foremost. Secondly open the valves (the two heat and chilly) to make constructive you have the water off. next do away with the faucet handles with a screwdriver (some have caps on suitable retaining screws which you will go with to pop off). some handles that have been on for some years would be problematic to get off, so as which you will %. to positioned money right into a sequence of cope with pullers. After removing the handles you will see a great nut, unscrew with pliers or crescent wrench and pull the stem out. If the stem is brass it could desire to have a rubber or plastic washing gadget on the backside hung on with the aid of a screw. do away with screw and bypass purchase same length washing gadget and replace it. If the stem is plastic then it could precise be washerless and you basically replace the completed stem, or it could desire to have a rubber cap washers and comes, look down contained interior the hollow the placement you pulled the stem from and word. if so replace the cap washing gadget and spring. Reassemble and alter water lower back on. solid fulfillment

Q:Bathroom wash basin faucet bad how demolition also how reload?

From the basin down the demolition, the following two hot and cold water pipes.