Tapsl Kitchen Handles Kitchen Aid Brass Tap

Ref Price:
$79.17 / pcs
Loading Port:
Shenzhen
Payment Terms:
TT
Min Order Qty:
50 Sets PCS
Supply Capability:
2000Sets Per Month PCS/month
Inquire Now Customer Service

Contact us by

(1) WeChat
(2) Whatsapp: +8617190086776

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Product Name:Tapsl Kitchen Handles Kitchen Aid Brass Tap
Description:
brass body
brass handle
brass cartridge
30cm flexible hose
brass parts
Chrome Plated
Carton Packing Size:45*43*44.5cm
About product:
1.High quality makes it more comfortable and durable.
2.It's easy for you to install the faucet correctly even if you never install faucets before.
3.The sink faucet is fashionable enough to make your house look modern.

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:water faucet?
if its a new installation it should be easy. you need a basin wrench, two 3/8 inch x 20 inch flexible steel braided faucet supply's, the new faucet and a flashlight. put down some rags under the sink (gets a little wet) close the valves under the sink and turn on the faucet to assure they are off and holding. remove the supply lines from the faucet and the valves you closed under the the sink. now loosen the capture nuts on the shanks of the faucet where the supply's were removed. after the captures are loose and removed the faucet lifts up and away. if there is a sprayer to the right of the faucet just cut the hose and remove it. the new faucet will come with installation instructions and pictures...so i won't have to write a novel here. if you get a basic faucet it will be simple... when you get into the exotics it becomes a strain. stay with a delta or a moen faucet...stay away from price phister...remember when you are purchasing a faucet... if there is an existing sprayer to the right of the faucet you will need to buy one with a sprayer (w/spray) don't want a sprayer and one exists...you will need a cock hole cover for it. talk to a sales person at a plumbing supply house....stay away from home improvement centers...best advise i can give you and good luck to you. yes there is a price dif between the supply house and home improv center...but you tell the guy at the counter in the supply house about it and many times you get a break. PLUS they know their product. good luck
Q:Three hole wash basin installed a single hole wash hands, the other two holes exposed how to do?
The first to block the glass with the second to do two shelves hanging on top of the watch and the like
Q:How do I remove old kitchen faucet plastic fasteners that are screwed on too tight (attached to metal pipe)?
I think you need a special plumbers tool called a "basin wrench" to get into the tight spot between the back wall and the sink where the nuts holding the faucet are found. Also stretch your back, legs, arms and neck and take some Motrin before contorting yourself into all sorts of unnatural postions when you work under the sink. Good Luck.
Q:Is the size of the washbasin single-hole double-hole faucet the same?
Pitch is the center of the standard 10 cm, is the same
Q:leaking faucet, how do i fix it?
Unless this faucet is near and dear to your heart, just replace it. Be sure to replace it with a good one, because the cheap plastic ones only seem to last two or three years. Your faucet isn't glued to the countertop, it's just attached via two or three plastic nuts. You have to get directly below the faucet (where the water connections are) and you should see what you need to remove to get the old faucet off. There is a special wrench called a basin wrench that you can use or you can just use some pliers. They can be very tight and hard to remove though since you won't have much room. Be sure you turn the water off before you do any work....
Q:Faucet doesn't "stop turning" HELP!?
More than likely the stop that on the stem has broken,common prob when faucet is tightened to much. You can take one out by removing the handle (usally held on by a screw somewhere,but beware you can strip out this screw pretty easy).When you get the handle off, it will usally take a pair of pliers to extract the stem(look for a big nut),after you loosen this or take it off,the stemm should pull out (again this may not be very easy,depending on the age).Take it to a hardware store and match it up. If the faucet is very old,I would probaly replace it,you can pick up a good faucet for 75.00 most places,if you do this invest in a basin wrench,it will save you hours of fun under a sink!
Q:8-inch faucet basin basin can hold 4-inch faucet you do
Can be installed, but a little loose, so the basin basin up and down to install a 4-inch hole with a rubber gasket, the middle also clip an 8-inch diameter, 4-hole hole, the thickness of the basin and the equivalent of Gasket, so that the faucet can be just in the 8-inch hole in the central position.
Q:Kitchen Faucet Removal Problem?
I used an adjustable wrench and a lot of Liquid Wrench (hardware store) to get mine off. Before you start unscrewing them, lay some cardboard or newspaper on the bottom of the shelf, put on some eye protection and spray liberally with W-D40 or Liquid Wrench and let sit about 5 minutes to soak in. Still wearing your eye gear, start unscrewing those big washers. Once you get them off, just pull off the lock nuts and the assembly.
Q:I am getting pebbles clogging up the cold water side of my bathroom faucet, whats up with that?
Could be calcium. You can flush it yourself but you'll likely need two people for the job. Turn off the water under the sink at the shutoff valve. Remove the faucet handle, then the valve stem(usually some kind of nut holds it on),then the seat and spring. Hold a cup upsidedown over the now open resivoir and have the second person turn the shut off valve ever so gently so the water flows at a manageable rate, hits the cup and goes down the basin. Let it run for a few minutes to clear the line. Put your faucet back together. Good Luck!
Q:Wash basin faucet double hole size how much distance
Now the new national standard basin double hole faucet distance is 102 mm.
We are very popular with consummate skill, advanced workmanship, perfect after sales service in the world. From now on, our company devotes ourselves to enterprise construction and development, market is the guide, management is the basis, science is power.

1. Manufacturer Overview

Location Kaiping,Guangdong
Year Established 2004
Annual Output Value Above RMB5 Million
Main Markets
Europe and the United States, Australia

Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port Guangzhou
Export Percentage
No.of Employees in Trade Department 4 People
Language Spoken: English;Chinese;
b)Factory Information  
Factory Size: Above 3000 square meters
No. of Production Lines 2
Contract Manufacturing OEM Service Offered;Design Service Offered
Product Price Range Average