Q:Why is the floor arch? How to handle the arch?

Floor from the arch reasons: 1, the floor was blisters, the floor volume increases, causing arch. 2, when the laying of the dry season, the old man was the tomb of the fat? Was fat to let the pack to protect the darling of the bite of the body was still strider Tu Tu smear vinegar Ao 簦 薮 薮 ρ 欤 蚨 蚨 ? Quail ah 3, the wall and the floor between the left did not stretch or stay too small, the floor is dry, moisture content is too low. 1, in case of arch, should first remove the skirting board, and in the arched with a large electric arc saw saw a knife, so that it is not because of continued expansion and then arch, and then observe a day or two, If it is no longer arched, replace the floor with the floor into a new floor. 2, if the arched serious, remove the skirting board Watshao off the shop broken off the water, the old floor, resurfacing, in the demolition, the floor surface damage, should be replaced by a new floor. 3, from the skirting board, once again reserved expansion joints; in the room and the room connection to install the buckle; re-install the baseboard, clean up the plaster, putty and other reserved expansion joints; from the floor, re-installed; Floor, ground treatment is flat, dry and then paved.

Q:Need to find other cleaner than pergo's brand cleaner that is unavailable to get floors clean and not leave foot prints behind after washed . also the stickiness always left behind

I use a micro fiber flat mop and Mr. Clean, I wash it and then a clean rinse, never had a problem, had my pergo about 15yrs.

Q:Can anybody describe what is exactly happen or how is it commence of the floor drift during earthquake/seismic/wind effect to a building?is there any animation that i can see from any websites?what does it mean of drift value of 4%? how does it calculate this?last question, what is the definition of cyclic load? can u giv some example?

Floor drift is movement of the floor system within tolerance by loads which occur randomly. A cyclic load is a repeating force on a body, such as the loads produced by the rotation of a turbine assembly .

Q:Does anyone have any experience with painting a wood floor white? How did it come out and how long did it last? Did it get dirty very fast?

All I can tell you is that I have white tile floors in my entire home and they are an absolute nightmare. They look clean for one day, that's it. The kitchen, oh, forget it, one meal and it's time to clean it again. I used to clean them every day for years and it's a big house. I finally gave up and clean them about 3 times a week. And if it rains, it's a real mess from footprints. Do yourself a favor, don't go with white.

Q:How is the floor greasy?

Take the right amount of household practical flour, evenly scattered on the surface containing greasy dirt on the floor. Between a moment, greasy is adsorbed on the flour, then gently wipe look, and then scrub clean with water can be.

Q:Is to use the floor of the VR texture map, the results of the whole floor on a piece, how to get the grid ah? Depressed dead, school interior design, hand-painted can be, and CAD and rotten, there is a harp harp ?  ?  ?  ?  ?  ?  ?  ?  ?  ?  ? 

Plus UV map, adjust the size of the brick.

Q:Would it be awkward to have tile on both the floor & counter top? We have white cabinets, stainless steel appliances & I want medium brown floors & counter tops...would this be weird?

Not weird at all, its all in the look you like. They make many tiles called modular tiles that come both in 2 sizes , a big tile and a smaller tile. For example a 12x12 and a 6x6 tile, These work for a floor / wall combination just as your doing.Or you can do a solid surface counter top and a smaller tile on the back splash to go with the floor tile. You don t have to do it that way but they should obviously compliment each other. Any questions you can e mail me through my avatar and check my qualifications there. GL

Q:what steps are needed to correctly install a linoleum floor

It all depends on how you want to put it down. It is very important to have a smooth sub-floor as most surfaces will transfer any imperfections to the new floor i.e. bumps,dirt,and even patterns from previous flooring. You can either do a floating floor, where you just lay it down. Then there is a full spread glue down, where you glue the entire surface of the floor down. finally, there is just doing a perimeter glue down where you just glue down the floor around the edges. It gets a little tricky if your room is larger than the usual 12' width that the flooring rolls come on and especially if you have a pattern match. Seams need to be very tight so they are not noticable. After the floor has been put down it need's to be rolled with a very heavy roller to adhere the floor to the glue and remove any air pockets left.

Q:Solid wood composite floor with enhanced floor than, which is good?

One of the top ten brands of laminate flooring: one of the top ten brands of flooring composite flooring: one of the top ten brands of composite wood flooring: one of the top ten brands of composite wood flooring: One of the top ten brands of flooring: Cicero flooring composite wood flooring one of the top ten brands: Parker floor composite wood flooring one of the top ten brands: Kenya floor composite wood flooring one of the top ten brands: Yangtze flooring composite wood flooring One of the top ten brands: macro resistant floor composite wood flooring one of the top ten brands: Kyrgyzstan as the floor to strengthen the durability Thank you to see these brands above it if the budget is enough, then multi-layer Solid wood is still possible

Q:I have 3 rooms with shinny floors. I use swifter wet every day and i mop using fuller floor shine once a week. My floors don't shine like it should. What can i use to get my floors to look shinny.

If your floors are wooden then to get them really shiny use bee's wax. It is a bit smelly, time consuming and hard work but worth it! If your floors are tiled then use Astonish no rinse wood floor cleaner. It is better than anything else I have found. If none of these work you could try using window cleaner ive never tried it myself but I reckon it would work!