Q:What does "10" in the butterfly valve "D71X-10" mean?

The pressure of 10 kg 1.0MPA is usually cast iron

Q:What's the difference between a butterfly valve and an eccentric butterfly valve? What is the difference in field applications?

Avoid friction and wear on the sealing surface!And, at the time of closing, and opening the opposite, there is a better sealing effect! Now generally use eccentric butterfly valve as the main. That's all I know! If there is any mistake, please forgive me!

Q:What does the triplex of pneumatic butterfly valve mean?

Upstairs is quite right, but now seems to use very little oil mist, and now generally referred to as "triple parts" as if: filter pressure reducing valve, solenoid valve, with the valve position feedback switch.

Q:D37A1X9-16CB1: what does this butterfly valve mean?

The model is composed of 7 units, the types of valves (gate valve Z, J, L, Q ball valve, throttle valve, check valve and H valve, butterfly valve, connection mode (D) internal thread 1 thread 2, welding flange 4, 6, 7, the clamp (0) electromagnetic transmission mode 1 solenoid valve, hydraulic, electric and hydraulic turbine are 2, 3, 4 and 5 gears, bevel gear, pneumatic hydraulic, 6, 7, 8, 9) pneumatic and hydraulic, electric, structure (straight or DC type 7,1 on behalf of the center plate, vertical type A (A) and LT X9) on behalf of a sealant is heat-resistant rubber, kg 16 kg, C represents the body material of carbon steel WCB, B1 on behalf of the valve plate is made of ductile cast iron plating)

Q:What's the difference between the three eccentric butterfly valve and the two eccentric butterfly valve?

The structure features that the center of the stem deviates from the center of the disc as well as the center of the body. The effect of the double eccentric valve can be opened immediately after the disc from the valve seat, substantially eliminating the unnecessary disc and valve seat over squeezing, scratching phenomenon, reduce the resistance from the open, reducing the wear and improve seat life. Three eccentric butterfly valve: to high temperature, must use hard seal, but the leakage is large; to zero leakage, must use soft sealing, but not high temperature. In order to overcome the double eccentric butterfly valve this contradiction, and the butterfly valve for third times eccentric. The so-called third eccentric, that is, the shape of the sealing pair is not a positive cone, but rather oblique cone.

Q:Transformer butterfly valve and pressure relief valve difference

The oil immersed transformer pressure release valve is a safety device installed in the transformer, when the internal pressure is less than the limit value of the transformer such as 35kPa, which is in closed state, when the transformer internal fault occurs, a large number of transformer oil by pyrolysis, produce large amounts of gas, the internal pressure of the oil tank increased dramatically when the opening pressure exceeds the pressure release valve when the pressure relief valve opens, the internal oil and gas overflow, to release the pressure, avoid the pressure on the inside of the lead tank cracking or permanent deformation, when the fault of transformer internal end, internal pressure tank to reduce pressure release valve closing pressure, it will automatically shut down to prevent outside air enter the inside of the tank or water.

Q:What is the effect of nylon coating on butterfly valve plate? Thank you

Mainly media will not be contaminated by rust on the body, you should say that the central soft sealing butterfly valve, the central valve is generally cast steel or cast iron material, so useNylon coatingLining up. There are soft seals, sealing performance is relatively high

Q:My quot;check engine soonquot; light came on yesterday and soon after that I took it to the nearest Midas to have the diagnostic test run on it - they stated I needed an ERG valve. I have no clue what it is and was told that it could run $160. - $300. for my 1900 Astro van. what is an ERG valve? I have noticed that my van has a low humming sound when I'm driving it.

The EGR valve is there to reduce nitrous oxide emissions and lower the temp of the combustion charge. This has the affect of reducing the octane requirement of the engine. This isn't a bad thing. When the valve hangs open, the thing will run bad at idle and could even die. The thing is, the valve could be perfectly fine and the sensor could be bad. Since some states won't give you a sticker if the light is on, you're probably stuck with replacement.

Q:Do you use the straight stem butterfly valve in the fire fighting engineering?

Bar valve bar, did not hear the bar with butterfly valve, ah, there are pairs of folder and hand wheel type bar

Q:My bike has now 6200 miles on the odometer. The manual says that a valve adjustment should be performed every 6000 miles. But the bike runs fine. Can I just have the valve checked or should I have them adjusted even though the bike is fine? What will happen if I just keep riding it?

First off you are suppose to take your bike back to have your valves adjusted after 500 miles. Anything later can cause problems. The motor is already broken in. why did you wait so long to have them adjusted ? Your vibration is the tire is not balanced right , take it else where. good luck