Butterfly Valve DN200 BS5163 with Hand Wheel Made in China
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 50 pc
- Supply Capability:
- 5000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1. Manual Wafer Butterfly Valve Description：
A butterfly valve is a valve which can be used for isolating or regulating flow. The closing mechanism takes the form of a disk. Operation is similar to that of a ball valve, which allows for quick shut off. Butterfly valves are generally favored because they are lower in cost to other valve designs as well as being lighter in weight, meaning less support is required. The disc is positioned in the center of the pipe, passing through the disc is a rod connected to an actuator on the outside of the valve. Rotating the actuator turns the disc either parallel or perpendicular to the flow. Unlike a ball valve, the disc is always present within the flow, therefore a pressure drop is always induced in the flow, regardless of valve position.
2.Main Features of the Manual Wafer Butterfly Valve
a)Cast hole. Flange connection meet ANSI 125/150# DIN PN10/16 BS4504 PN10/16 in the meanwhile.
b)Soft seat. Replaceable. Increase of service life.
c)Double half shaft without pin.
d) Square and short neck. Easy to stick scutcheon and cost saving.
3. Manual Wafer Butterfly Valve Images：
4.Manual Wafer Butterfly Valve Specification：
1)Size: DN40-DN1400
2)Material:body-CI/DI/WCB/SS
disc:DI/CF8/CF8M/C95400
3)Professional Maufacturer for more than 10 years
PRESENTATION:
1) Sizes:
DN40mm-DN1400mm
2) Materials:
a) Body: CI(cast iron ,GG25 )/ DI (ductile iron ,GGG40)
b) Disc: DI / CF8 / CF8M / C95400
c) Seat: EPDM / NBR / TEFLON / VITON
5.FAQ
1. What is manual wafer butterfly valve?
A: Wafer style is the more common of the two and is less expensive than the lug style. The wafer style butterfly valve is just about the standard. It ís so common that no one even bothers to use the word "wafer" when ordering a butterfly valve. It is taken for granted that if a butterfly valve is ordered, a wafer style will be received.
2. How about the Installation of the Wafer Style Butterfly Valve?
A: Butterfly valves are installed by inserting the valve between two flanges using bolts or studs and nuts to hold it all together. This type of installation, of course, makes it impossible to disconnect just one side of the piping system from the valve. That benefit is received using the lug style valve.
3. What is the working principle of manual wafer butterfly valve?
A: A butterfly valve is from a family of valves called quarter-turn valves. In operation, the valve is fully open or closed when the disc is rotated a quarter turn. The "butterfly" is a metal disc mounted on a rod. When the valve is closed, the disc is turned so that it completely blocks off the passageway. When the valve is fully open, the disc is rotated a quarter turn so that it allows an almost unrestricted passage of the fluid. The valve may also be opened incrementally to throttle flow.
- Q: The difference between butterfly valve and gate valve
- Its varieties and quantities are still expanding, and the development of high temperature, high pressure, large caliber, high sealing, long life, excellent regulation, as well as multi-function development of one valve. Its reliability and other performance indicators have reached a high level. Disadvantages, there is a certain resistance to the medium. Gate valves are more used in steam pipes and large diameter water supply pipelines, because of the general requirements of fluid resistance is small, the use of gate valve. Valve is hand wheel rotation, stem upward movement. Flow is not the same, the gate valve requires full open. Need a higher installation space, the valve sealing surface has a certain self sealing capacity, its spool by the media pressure closely with the valve seat sealing surface contact, to achieve tight leakage.
- Q: I want to switch off the water in the bathroom only due to replacing sink taps, will water still come out of the pipe if i turn the stop valve
- Only water what is still in the pipes will come out but you will lose all your hot water in the hot water cistern if you have that type of hot water storage tank.
- Q: What is the electric butterfly valve? Please, great God!
- The output signal is stable and reliable for a long time. The valve has an electric node, which is drawn out to the control center by signal line, and the signal line voltage is 12V. In fact, the valve is open and closed, there is a signal to the consumer control center, easy to monitor, the valve in addition to the electric node, with the ordinary valve is not much difference, there are also signal butterfly valve.
- Q: What's the difference between D71X-16 and D71H-16 butterfly valves?
- D71X-16 and D71H-16 butterfly difference is that the cut-off is not the same, the latter is stainless steel seal, corrosion resistance, friction, acid or impurities can be medium fluid. The former is rubber sealed, only through the general temperature of the medium, not acid, with more, you can ask Luoyang crown Ning
- Q: What's the difference between a clip type turbine butterfly valve and a flanged turbine butterfly valve?
- For clip butterfly valves, there are no flanges at the ends of the butterfly valve. There are only a few guide bolts. The valve is connected with the end flange with a set of bolts / nuts.In contrast, the demolition to facilitate some of the lower cost of the valve, but the drawback is that a sealing surface problems, the two sealing surfaces have to be taken apart.Flange butterfly valve at both ends of the flange, and pipe flange connection. The seal is relatively more reliable, but the valve is of relatively high cost.
- Q: I have a 1993 Oldsmobile Cutlass Supreme and I think I have the case of the blow-by. The engine had high mileage, but was rebuilt b/c it stalled while driving. 3.1L V6 gasoline engine. The fuel filter and the fuel pump are brand new. Now we have the same problem a few months later. It stalls while driving. Its been sitting a while and won't start by itself, so I pulled off the air intake hose off of the air filter to spray starting fluid into it. I noticed oil puddled in the air intake hose, so I looked for the PCV valve on the rocker cover. There is a tube going from the air-intake hose to the rocker cover. I popped out the tube from the rocker cover and there is no PCV valve. Just tube. Is that where the PCV valve is supposed to go? If not, where can I find it on the engine? And could that possibly fix the blow-by and the stalling engine? I'd appreciate any help. Thanks in advance.
- top of the manifold
- Q: What's the difference between turbine butterfly valve and manual butterfly valve?
- Butterfly (Manual butterfly) butterfly plate installed in the direction of the diameter of the pipe. In the butterfly valve body cylindrical channel, the disc shaped disc rotates around the axis. The angle of rotation is between 0 and -90 degrees. When rotating to 90 degrees, the valve is fully open.Butterfly valve structure is simple, small size, light weight, only by a few parts. The utility model can be rapidly opened and closed only by rotating 90 DEG, the operation is simple, and the valve has good fluid control characteristics. When the butterfly valve is in the fully open position, the butterfly plate thickness is the only resistance when the medium passes through the valve body, so the pressure drop produced by the valve is very small, so the flow control characteristic is better. Butterfly valve has an elastic seal and metal seal, two types of seals. Resilient sealing valve. The sealing ring can be mounted on the valve body or attached to the periphery of the disc.
- Q: Water supply pipe gate valve and butterfly valve which good?
- 2. ball valve: ball valve with a central opening of the ball as the valve heart, the rotation of the ball control valve opening and closing. The ball valve has the advantages of simple structure, light weight compared with the cut-off valve, the sealing surface has the advantages of simple structure, easy processing, good sealing performance, convenient operation, switch quickly, but can not be used to adjust the flow, suitable for high pressure (up to 320 psig) pipeline, at present, the packing material limit, can only be used for 200 DEG C, can also be used a variety of media and the viscosity of the suspension.3. butterfly valve: butterfly valve, also known as turn over plate valve, is a simple structure of the valve. As butterfly valve should not be closely matched with the pipe wall, only applicable to regulating flow, can not be used to cut off the pipeline, often used in conveying air and flue gas pipe to regulate flow. Butterfly valve is with the stem rotation of the circular butterfly plate for headstock parts, in order to achieve the opening and closing action of the valve. Butterfly valve is mainly used with shut-off valve, can also be designed to adjust or cut off and adjust the function. At present, butterfly valves are used more and more in low pressure medium and large diameter pipelines.
- Q: How does the pneumatic butterfly valve control the angle of opening?
- This is really not good, control seems to be pneumatic defects, can only rely on the feeling
- Q: Butterfly valve, two-way pressure and one-way pressure what is the difference?
- One way sealing butterfly valve is the front of the butterfly valve. When it closes, it must face the direction of the medium. The medium flows only in one direction, and the arrow on the valve body indicates the direction of the flow direction of the medium. Attention should be paid to the flow direction of the medium during installation. Two way butterfly valve is butterfly plate can face or back to the media flow direction, installation without attention to medium flow direction, in the valve body also does not indicate the direction of the medium flow arrow. Two way sealing butterfly valve stem force is greater than one-way butterfly valve stem. Design, the same diameter, pressure butterfly valve, two-way sealing butterfly valve rod diameter than one-way sealing butterfly valve stem diameter.
Send your message to us
Butterfly Valve DN200 BS5163 with Hand Wheel Made in China
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 50 pc
- Supply Capability:
- 5000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
