Butterfly Valve DN150 Turbine Type BS 4531
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 50 pc
- Supply Capability:
- 5000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1. Manual Wafer Butterfly Valve Description：
A butterfly valve is a valve which can be used for isolating or regulating flow. The closing mechanism takes the form of a disk. Operation is similar to that of a ball valve, which allows for quick shut off. Butterfly valves are generally favored because they are lower in cost to other valve designs as well as being lighter in weight, meaning less support is required. The disc is positioned in the center of the pipe, passing through the disc is a rod connected to an actuator on the outside of the valve. Rotating the actuator turns the disc either parallel or perpendicular to the flow. Unlike a ball valve, the disc is always present within the flow, therefore a pressure drop is always induced in the flow, regardless of valve position.
2.Main Features of the Manual Wafer Butterfly Valve
a)Cast hole. Flange connection meet ANSI 125/150# DIN PN10/16 BS4504 PN10/16 in the meanwhile.
b)Soft seat. Replaceable. Increase of service life.
c)Double half shaft without pin.
d) Square and short neck. Easy to stick scutcheon and cost saving.
3. Manual Wafer Butterfly Valve Images：
4.Manual Wafer Butterfly Valve Specification：
5.FAQ
1. What is manual wafer butterfly valve?
A: Wafer style is the more common of the two and is less expensive than the lug style. The wafer style butterfly valve is just about the standard. It ís so common that no one even bothers to use the word "wafer" when ordering a butterfly valve. It is taken for granted that if a butterfly valve is ordered, a wafer style will be received.
2. How about the Installation of the Wafer Style Butterfly Valve?
A: Butterfly valves are installed by inserting the valve between two flanges using bolts or studs and nuts to hold it all together. This type of installation, of course, makes it impossible to disconnect just one side of the piping system from the valve. That benefit is received using the lug style valve.
3. What is the working principle of manual wafer butterfly valve?
A: A butterfly valve is from a family of valves called quarter-turn valves. In operation, the valve is fully open or closed when the disc is rotated a quarter turn. The "butterfly" is a metal disc mounted on a rod. When the valve is closed, the disc is turned so that it completely blocks off the passageway. When the valve is fully open, the disc is rotated a quarter turn so that it allows an almost unrestricted passage of the fluid. The valve may also be opened incrementally to throttle flow.
- Q: What does butterfly valve nps12cl150d373f4-150lb stand for?
- NPS (Nominal, Pipe, Size) abbreviation. Refers to the connection (including flanged and welding end) of the nominal diameter, followed by a digital unit is American Standard inches, 12 inches.NPS12 labeling system.CL is the abbreviation for class, and LB150 means the pressure is 150 poundsD stands for butterfly valves3 is expressed in the form of a turbine drive7 means of connection: to clip3 means sealing: 3 eccentricF4: the sealing material is PTFE
- Q: Butterfly valve general use occasions
- Butterfly valve general use occasions:1 、 soft sealing butterfly valve applies to ventilation, dust removal pipeline two-way opening and closing and adjustment, metallurgy, light industry, power, petrochemical systems, gas pipelines and waterways.2, metal sealed double eccentric butterfly valve, suitable for heating, steam, water and gas, oil, acid and other pipelines, as the adjustment and closure devices.3, metal seal three eccentric butterfly valve, in addition to as large pressure swing adsorption gas separation control valve.4, metal seal three eccentric butterfly valve, can be widely used in petroleum, chemical, metallurgy, electricity, food, medicine, water supply and drainage, gas transportation and other fields.
- Q: Water supply pipe gate valve and butterfly valve which good?
- 1. gate valve: also known as gate valve or gate, there is a valve in the valve flow direction perpendicular to the medium, adjust the height of the gate, you can adjust the flow of fluid. Valve advantages are small resistance, close tight, no water hammer phenomenon, widely used in a variety of liquid and gas shut-off valve. It also has some adjustment function, but when the part is opened, the gate is easy to be wetted by the fluid. When the fluid flows, it causes the shaking of the alarm board and the sealing surface is easy to wear. The drawback of the gate valve is that the structure is complex, the price is more expensive, it is difficult to repair, and the solid material is easy to deposit in the valve seat groove. Therefore, it is not suitable for the pipeline containing fiber or solid material in the fluid. Commonly used in the air, steam, oil medium pipeline, but also used as vent valve and low silk system valve.Gate valve is commonly used as one of the cut-off valve, mainly used to connect or cut off the medium in the pipeline, not applicable to regulating medium flow. Valve is suitable for pressure, temperature and caliber range, especially for medium and large diameter pipes.
- Q: Fire, the signal butterfly valve flange connection or welding?
- Grooved flange joint, welded flange connection! Wire bonding. Wire to flange connection! In addition, you can choose the groove type signal butterfly valve!
- Q: What are single eccentric and double eccentric in butterfly valves? What's the difference, please explain in detail?
- Double eccentric butterfly valve: in the single eccentric butterfly valve on the basis of further improvement of forming, is the most widely used double eccentric butterfly valve. The structure features that the center of the stem deviates from the center of the disc as well as the center of the body. The effect of the double eccentric valve can be opened immediately after the disc from the valve seat, substantially eliminating the unnecessary disc and valve seat over squeezing, scratching phenomenon, reduce the resistance from the open, reducing the wear and improve seat life.
- Q: I have put a new pressure valve and replaced both thermostat
- If you have replaced the TP valve, more than likely there is a heating element shorted to the tank. This will cause continuous heating and high temp/high pressure...good luck.
- Q: What is the butterfly valve
- Double valve technology is the use of large sets of small valve valve technology, place a small butterfly in the large butterfly valve, when feeding in a large number of double valves open at the same time, the material quickly added, when the material is in accordance with the set to a certain number, the valve automatically shut down, by a small valve to feed, until it reaches the requirements of the control system the number of closed, so as to ensure high precision batching material, thereby saving expensive raw materials.
- Q: Whenever sports cars are referred, people talk in terms of 'valves'. ex: v8, v12 etc. What does this all mean? Also they sometimes say that a v8 makes a great noise. why? How does the number of valves effects the performance? Many thanks.
- the v is in reference to the motor its in a v formation v8 4 cyliders on each side v6 3 per side v12 6 pre side now the valves is how many are in each cylinder you usually have 3 or 4 valves per cylinder the more valves the more horsepower the more cylinders the bigger the engine
- Q: How do the butterfly valves d341 and d343 differ in appearance?
- Under normal circumstances, 41 is soft seal body, 43 is hard sealing valve body
- Q: 1988 volkswagon cabriolet, rabbit tried mystery oil let sit for a week having trouble with stuck valves even taken a wrenrch to manually unstick. help any suggestions 4 cyclinder car has been sitting up for about 4 years
- The only reason for a stuck valve is if it bent from a thrown timing belt. Sitting 4 years will not cause valves to stick usually, because there is always some oil leakage from the head, that prevents rust. How do you know the valve is stuck? Have you done a compression test, checked the valve clearance? When you say you take a wrench to manually unstick it, it would help to know what you mean, because there is no place to put a wrench that would help unstick a valve that was stuck. You need to tell us much more.
Send your message to us
Butterfly Valve DN150 Turbine Type BS 4531
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 50 pc
- Supply Capability:
- 5000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
