Q:How many moulds can the 80 ton injection molding machine put down?

Should say how much pressure grams of machines, manuals, and you ask

Q:Injection molding machine, blister machine, blow molding machine, what is the fundamental difference?

Injection molding machine - a machine that produces plastic products by filling the mold with pressure.

Q:What is low voltage protection (injection molding machine)?

Protect the mold. Never press dies during production

Q:Seek advice! Is there a better low-pressure injection molding machine? After the sale well, which friends can introduce, thank you!

As far as I know, the low pressure injection molding machine produced by Connie Technology Co., Ltd. is especially good and provides full range of technical support, which is rich in New Technology

Q:Is this an injection molding machine?

It's an injection molding machineInjection molding machine, also known as injection molding machine or injection machine. It is a thermoplastic or thermosetting plastic plastic molding mold made of plastic products of all shapes of the main molding equipment. It is divided into vertical, horizontal and all electric type. The injection molding machine heats the plastic, applying high pressure to the molten plastic to make it crack and fill the mold cavity.

Q:Why is the power of the motor different?1. the same 90T why some motor power 8.5KW, some 11KW, and some 15KW?.2. why are there so many power points? Is it possible to produce the same product with 8.5KW? Is it okay to use 11KW?3. what's the difference between 8.5KW and 11KW? Isn't the power of the bottom more power saving? Or is the power clamping force less than 900KN?4. if the 8.5KW clamping force also has 900KN, then the 11KW clamping force is also 900KN, is that the way it is understood? So 11KW isn't a waste of electricity?Give high marks to adopters!!!

Small screw, injection pressure will be much larger, such as a bar to let you plug in the wood, may be more difficult, if you use a needle in the wood is much easier, the small screw is suitable for precise, thin-walled products, is the need to install the nitrogen injection really do thin-walled products or hydraulic machine. All electric injection molding machine, if you just the production of ordinary products, injection molding machine is basically on the market can meet (limited to hundreds of tons of clamping force of the machine), a large Haitian machine is a good choice

Q:Recommend durable low pressure injection molding machines?

Low pressure injection molding machine is mainly used in the encapsulation and protection of precise and sensitive electronic components. Low pressure injection molding process is the injection pressure uses a very small (0 ~ 6MPa) package material is injected into the mold and rapid curing (5 to 50 seconds) of the packaging process, so that products meet the insulation, temperature resistance, impact resistance, vibration, moisture-proof, waterproof, dustproof, chemical corrosion and so on performance. It is widely used in many fields, including: printed circuit board (PCB), automotive electronics, automotive wiring harness, automotive connectors, sensors, micro switch etc..

Q:How many grams of 200t injection molding machine?

Heating part energy saving: heating part energy saving, mostly using electromagnetic heater energy saving, energy saving rate is about 30%-70% of old resistance ring.1. compared with the resistance heating, the electromagnetic heater has a layer of thermal insulation layer, and the heat energy utilization rate is increased.2. compared with the resistance heating, the electromagnetic heater acts directly on the tube heating, reducing the heat transfer and thermal energy loss.

Q:General injection molding machine agents need what conditions?

This is to ask manufacturers, each manufacturer of different

Q:transparent parts inside the bubble, how to solve this problem, non -, what is the cause?

It is a bit complicated, did not see the kind, generally there are two possible reasons: one is that there may be more humid caused the raw materials, WIP bubbles appear relatively thick, dense and bubble like you; this can be ruled out, there is a lack of a little exhaust design mold. Specific reasons to see objects in order to determine! I wonder if I can help you.