BX3 AC Arc welder
1.low operation noise
2.best working performance
3.apply to mild steel, stainless steel, alloy steel
BX3 AC Arc welder
Features and parameters
Its electric arc is soft and very stable
Moving coil transformer structure has low operating noise and fine ability.
Bare copper flat wire technology is adopted for wire package, with asbestos insulant as bedding to realize quick heat dissipation, high efficiency and long working life.
The unique BX3-630 welder adopts high no-load voltage design, suitable for reinforcing steel bar vertical butt welding. It`s the first choice to select for steel bar vertical but welding.
Welding material: low carbon steel, high strength steel, medium carbon steel, low alloy stee.
Main technical parameters
Rated Input Voltage(V)
Rated Output Current(A)
Raged Duty Cycle(%)
Rated Input Capacity(KVA)
- Q:Used welding machine welder, argon arc welding machine for sale
- You can register on the home of the welding website and publish the second-hand information, which is very convenient and quick!
- Q:Is your argon arc welding machine a two phase home? What's the size of an argon cylinder?
- There are two phase, but less power, decoration and decoration seems to be no problem.
- Q:Which brand of AC arc welding machines is of the best quality?
- First name: Miller good welding effect, concentrated arc, strong firepower. Especially the effect of welding of aluminum is the most outstanding. In addition to this brand welding machine especially durable. If an enterprise is allowed if economic conditions I strongly recommend this brand.Second place: Tangshan Panasonic: the advantages of welding function is all. Welding effect is very good, especially stainless steel small current arc success rate. Shortcomings: performance is not stable, repair rate is high. Service life is shorter than MillerThird: Shenzhen reallink quality, the biggest advantage of this card machine low price good. The average user is strongly recommended.Fourth: the general quality of the TIG welding machine the biggest drawback of Japan OTC the two Danish migatronic brand, high price. Strictly speaking migatronic a little better.Fifth: Shanghai Weiteli welding stainless steel has the advantages of good effect, good arc welding of aluminum arc. The shortcoming is too hard. The price is reallink much higher.
- Q:How does argon arc welding gas?
- Do not weld in a windy place and turn down the argon to the point where the quality of the welding is not high enough to be welded. Can also put some small gas delay time, and advance aspirated can turn off the machine.
- Q:What does the base current and the peak current mean on an argon arc welding machine? How to adjust?
- The range of the maximum no-load voltage is not good. The machine itself is set up
- Q:Making stainless steel burglarproof window, what argon arc welding machine is used?
- Is it necessary to use argon arc welding for stainless steel windows? With stainless steel electrode can be, and if you want to shape well, after welding, sandpaper polished, you can.If you must choose argon arc welding, the general welding machine has two functions of electric arc welding and argon arc welding, welding of stainless steel window does not need too much current, buy a small box (to sell machine where you will understand that it is not expensive), with convenient
- Q:Argon arc welding machine does not arc, ground wire, welding torch is normal, what's the matter?
- 1: welding current is too small. Increase the welding current.2, the tungsten electrode burns badly, and the tungsten electrode is seriously oxidized, which leads to high resistance and difficult to arc. Regrinding tungsten electrode can be done.3, high frequency plate, high frequency ignition, discharge electrode burning, or serious oxidation, resulting in weak discharge. Use fine sandpaper to polish the electrode and replace the new electrode when necessary.4: welding machine in the high-frequency version of aging or damage. Check and trouble shooting, replace high frequency board when necessary.
- Q:Circuit diagram of WS-160 DC argon arc welding machine
- Performance characteristics: welding current minimum, from 10A (except WSE-180), stable arc performance, welding thin, medium and thick plates. DC pulse argon arc welding is suitable for welding stainless steel, copper, titanium, carbon steel and other materials. Besides, the characteristics of sag and descent can be obtained, and the welding current waveform is a square wave with fast zero crossing, which is beneficial to welding current and arc stability. AC argon arc welding is suitable for welding aluminum, magnesium alloy and other materials. By adjusting the pulse current and pulse frequency, the weld width, penetration depth and the number of weld ripples are controlled, and the weld seam is even and beautiful. Pulse time, pulse base time, atomizing zone regulation, gas lag and turn off time are all regulated without polarity, which can meet the requirement of higher welding process. It has the functions of AC and DC argon arc welding, AC and DC pulsed argon arc welding, AC and DC manual general welding, AC and DC spot welding. With welding current slow rise and decay functions are conducive to the current arc attenuation to fill the crater, avoid cracks.
- Q:How can the alternating current welding machine change the argon arc welding machine?
- 1, can be directly connected to the argon arc welding torch, of course, have to connect the gas road, the current to the desired position, the line of arc (that is, contact short circuit, arc), direct welding can be2, note: welding torch negative electrode
- Q:Argon arc welding without arc welding -- Shanghai universal argon arc welding machine WSE-315-1
- If it is not out of line transformer are bad phenomenon, usually due to electric shock in the short distance from the picture above transformer, high frequency discharge energy shortage, suggestions will shock large distance try.
Our company is a new high-tech enterprise specialized in the study, development and production of AC, DC, Inverter TIG and Special welders. Our company has superior production equipment and high quality control system. We adopt modern management system up to standards of ISO9001:2000. All of our products have got our national CCC certification and Canadian CSA approval, and also comply with UL standard for American market and CE certification for European countries.
1. Manufacturer Overview
|Annual Output Value
||30.00% Domestic Market
10.00% Mid East
10.00% South Asia
5.00% South America
5.00% Eastern Europe
5.00% Eastern Asia
5.00% Southeast Asia
5.00% Central America
5.00% Northern Europe
5.00% North America
3.00% Western Europe
2.00% Southern Europe
||US$5 Million - US$10 Million
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||41% - 50%
|No.of Employees in Trade Department
||30,000-50,000 square meters
|No. of Production Lines
||OEM Service Offered
|Product Price Range
||High and/or Average