Q:what are the step i need to do so i can change the valve seals my truck has been smoky.,,, any websites i want todo it myself... 1989 chevy silverado 2500 350 engine 5.7L

First find out if that is the issue. Do a wet/dry compression on all the cylinders. That is where you do a compression test on all the cylinders and write them down. Then squirt about three pumps of oil from a oil can into each cylinder and retake the compressions. If the compressions don't change and are low, the valves are burnt and you need a valve job. If the compressions go way up after the oil seals the rings, then the piston rings are bad and the engine needs rebuilding and that may be where the oil smoke is coming from. If all the cylinders are within 20 psi and runs good, then it may be your valve guide seals are bad. You can replace them without pulling the heads. You can go to an auto parts store and buy a valve spring compressor that is used while the head is on the block. It has an air fitting that screws down into the spark plug hole and when filled with compressed air, holds the valves up while you remove the spring and replace the valve guide seal.

Q:Buried extension butterfly valve is buried or need to repair the valve well, can build the valve well, the extension rod butterfly valve installed in the valve well, the extension rod to avoid covers, the top of the valve well out, so that the hand wheel in the ground operation.Atlas S143 is less than the inner diameter of DN150 valve wells only 1200mm, DN200-DN250D diameter of only 1400mm, 700mm valve covers, valve rod and a handwheel to lengthen through the valve cover, valve wells is built to cover the embedded pipe or tube? Is there a standard atlas?

The establishment of a repair valve well, easy to repair, usually hydrogen long rod butterfly valve installed in the well. But if the quality of buying long stem butterfly valve, it can also be buried directly, not easy to bad

Q:What is the butterfly valve

From the working principle of double butterfly valve can be seen that the operation is simple and easy to use, almost no wearing and maintenance compared with traditional ingredients.

Q:Function of signal butterfly valve in fire sprinkler system

The signal butterfly valve is connected with the fire alarm system to monitor the switch status of the valve, thus effectively preventing misoperation

Q:What's the difference between a butterfly valve and an eccentric butterfly valve? What is the difference in field applications?

Eccentric butterfly valve and ordinary butterfly valve, when the butterfly valve is opened, the eccentric butterfly valve sealing surface will reduce great wear, in the opening, the disc will leave the valve at the first time the sealing surface!

Q:When will Butterfly Valves be used?

Butterfly valve is the most common and most widely used in the field of the valve, cases of sewage treatment, water supply, iron and steel, building construction and heating fields needs a lot of valves, especially with the hard seal butterfly valve butterfly valve position and a lot of popularity, the field is used more widely.

Q:For example, the arrow above is from left to right, and the direction of my current is from right to left. Is that ok? I have a diameter of 700 of the hard seal butterfly valve is so installed, but it will leak water, it will not leak, very serious

The direction of the arrow on the valve body refers to the direction of the medium.Also known as butterfly valve, control valve has a simple structure, can be used for low pressure pipeline valve switching control is closed parts (disc or disc) is a disk, around the valve axis to achieve the opening and closing a valve, the valve can be used to control the flow of air, water, steam steam, all kinds of corrosive medium, mud, oil, metals and radioactive liquid media and other types of fluid. On the pipeline, mainly from cutting and throttling. Butterfly valve headstock is a disc shaped disc, in the valve body around its own axis of rotation, so as to achieve the purpose of opening or closing or regulation.

Q:Classification of telescopic butterfly valve

2) additional torque seal butterfly valve. The seal is produced by a torque that is applied to the valve shaft(2) pressure sealed butterfly valve. The pressure is greater than the pressure on the seat or plate(3) automatic sealing butterfly valve. The pressure of the seal is automatically generated by the pressure of the medium. (1) vacuum butterfly valve. Butterfly valve with lower working pressure than standard atmosphere.(2) low pressure butterfly valve. Butterfly valve with nominal pressure PN<1.6MPa.(3) medium pressure butterfly valve. Butterfly valve with nominal pressure PN 2.5--6.4MPa.(4) high pressure butterfly valve. Nominal pressure PN is 10. 0--80.0MPa butterfly valve.(5) ultra high pressure butterfly valve. Butterfly valve with nominal pressure PN>100MPa. (1) high temperature butterfly valve. T>450 C butterfly valve

Q:How can I get the fire signal butterfly valve?

After the switch is closed, the alarm is output through the output module.

Q:D341W-10P-400 butterfly valve, what does each alphanumeric letter mean?

According to JB/T308-2004 "valve type programming method"D butterfly valve3 worm gear4 flange connection1 Structure: sealed type, central vertical plateW sealing material for valve body material10 nominal pressure PN10P body material is chromium nickel stainless steel400 shall be nominal size DN400