Q:Im cleaning up some of the wires in the engine bay and getting rid of ones i dont use. Right now theresthe pos side bat post runs down to the starter. From the starter there is a thicker wire and a skinny wire. In the thicker wire there is a wire that goes to the post on alternator. Both wires from starter run over to a relay maybe ithas a stud sticking out and has a wire that goes from the bottom of it to the fuse box. Im in middle of relocating the battery into the trunk so what wires can i eliminate and what wires have to go,to the battery?

Like Mikey reported for starter and alternator it is not appropriate. in case you think of issues have been swapped there are various strategies over the 40+ years that Chev made the classic small block. Assuming that's a Chev motor there are in basic terms 2 starters and the version is the place the mounting bolts are. One version the bolts are in the present day for the time of from one yet another and the different form they're offset. most of the engine blocks have the two contraptions of holes so it relies upon on the flywheel which one is needed. Alternator could be slightly extra challenging to verify. countless strategies will bodily in superb condition then you definately've the pulley form, connector type and charm and orientation. you will be able to ought to snap some pictures and desire for an surprising guy on the aspects save or carry the previous one in and tournament it up.

Q:I have 12/3 wire running from the breaker box on a 20 amp breaker that powers a bathroom (2 lights and 2 receptacles). I want to splice into this and run 14/2 wire into the living room to run 6 recessed lights. Is this OK to do?

No you should either use a 20 amp breaker and 20 amp recepticles or if you use a 15 amp breaker then use 14/2 or 14/3 wire. Too heavy of wire creates a fire risk. If your new home was wired to code, this seems quite odd.

Q:I just learned how to do 3-way wiring, so that I can turn a light off from 2 different switches. My question is, how do I add another light to that mix, so that both lights come on/go off at the same time when I turn the switches on and off? (It's for a closet that has 2 lights in it that I want to come on/go off at the same time).

You have to tie the wires that go to the light together. It is called parallel.

Q:I have an old house and am replacing a dimmer switch in the kitchen.The old switch is has only 2 wires coming out of the switch that are both black. From the wall 2 wires connect to the 2 black wires on the switch, one is black which I have concluded is hot and the other is red, which must be the common wire. My question is that there is a 3rd wired that is pushed into the electrical box that is capped and not being used. This wire is white. I can only assume that would be a ground wire, but why would it be white in color. Can you tell me what the coloring scheme was for wiring old houses? Now I can connect the switch and use only the black and red wire, but would like to ground it properly if possible.

This Site Might Help You. RE: what do wire colors mean (old house)? I have an old house and am replacing a dimmer switch in the kitchen. The old switch is has only 2 wires coming out of the switch that are both black. From the wall 2 wires connect to the 2 black wires on the switch, one is black which I have concluded is hot and the other is red, which must be...

Q:Not the wire from RadioShack, but the really thin stuff used in modded circuit boards, logic circuits, low power circuits, etc.

Use telephone cable,inside has more than 20 pieces of single wire. Or using ethernet cable,inside has 8 pieces of single wire.

Q:ive heard multiple people talk about a 'final wire'. what is it exactly? Is it the thickest wire possible? Or is it when you havent gotten your wire changed in a while?

The final wire is, as its name implies, the very last wire that will be used before your braces comes off. It is usually either a square or rectangular wire and braided. The wire is used to do the final tweaking on your teeth and to close any minor gaps you may still have. And YES, it is the thickest wire you will wear.

Q:what are the ground and power wires for a walmart replacement cigarette lighter?

In answer to your question, there is no difference in the wires because a lighter element isn't polarized, in other words, hook either wire to positive, and the other to ground. That's why both wires are black.

Q:i have a 1995 chevy S10 blazer and i noticed that it has 5? speakers in the door and 6x9 in the back i started looking and i found that it has 4x6 in the dash with cardboard over it but it don't have speaker wire ran for it i think its going to be difficult running wire for it but what gauge of wire should i use? and should i run the speaker wire to the head unit how would i hook the speaker wire to the aftermarket head unit or should i run it to the 6x9 or 5? i already have a pair of 4x6's ready to be installed in it as soon as i find out how to do it and what size of speaker wire it is im going to be doing it by myself

16 okorder /

Q:What are the range specs when testing resistance on your spark plug wires ?

RE: What range in ohms are spark plug wires normal? What are the range specs when testing resistance on your spark plug wires ?

Q:Hey there, so my cat chewed through some of my wires, what should I do to like fix them?

If the wires are not chewed apart completely, and the two wires are not touching each other you can just use black electrical tape.