Q:Gypsum board has no formaldehyde

No Gypsum board is a very good environmentally friendly decorative materials, the main material used for the gypsum and paper, it is environmentally friendly non-toxic decorative materials, Europe and the United States the proportion of gypsum board is much higher than China, China's future interior decoration ceiling interval The proportion of gypsum board used will be greatly increased.

Q:Hi! I want to hang my electric guitars on my wall which is made of plasterboard! Each guitar with have it's own hanger with two screws holding it on the wall. I will also use plasterboard wall plugs to hold the screws in place> I am just wondering if the walls will be able to support the weight of the guitars at all or is this going to be a disaster? Thanks all!

electric guitars are typically pretty heavy. seriouosly,, i wouldnt rely on plasterboard for the support of the weight. enlist the use of a stud-finder and using long enough screws (1 1/2 inch ) mount the guitar hook deep into the beam through the plasterboard or you may find them on the floor and broken.

Q:Can I remove a raw plug from a wall without badly damaging the plasterboard?

Best just to punch it in, and plaster over the hole, less damage that way

Q:Need to know how much the nail a box of money

Speak brand, good brand nail amount of foot, material is good, the price will be appropriate high point!

Q:Ask the wall, that top of the ceiling with gypsum board, the above can be directly painted it? Still have to do putty ah?

Gypsum board, whether it is the ceiling and the wall, are to be used to seal the screw screw cap, gypsum board slot caulk putty embedded, and then paste the gap with the grid cloth, and then two to three gray, and then paint.

Q:ive bought metal anchor bolts to fix semi pesistal basin to wall(4) but im not sure if its strong enough to hold it.i also cant work out how to connect same diameter waste pipe(cummin out of wall) to chrome waste trap?please help.

If the wall is drylined this is the plasterboard is caught onto the blocks with blobs of adhesive, then the hollow between the plasterboard itself and the breeze block is maybe to be decrease than 0.5 an inch. Drill rapidly interior the path of the p.b and into the blocks then use the variety of long fixing plugs and screws used for fixing doorframes to partitions. a similar style of fixings could be utilized if the wall is battened although care would desire to then betaken to no longer tear a hollow interior the p.b. once you tighten the screws.

Q:I have some old style plasterboard in my house and I was wondering if there is any good way to smooth it out so it matches my new drywall? I'd rather not have to take it down but if it comes to that i'll do it. I am going to be texturing the new drywall. Could I just spray the texture on the old stuff and maybe hide it enough to get by?thxJoe

My brother faced this dilemma in a house he remodeled. He ended up tearing out the lath and plaster and replacing it with sheetrock - less work than refinishing the old stuff.

Q:We have recently had a fairly big extension and now a considerable amount of our walls are plasterboard. I had painted one room a couple of months ago and now some of the screws have popped through from the plasterboard. I am now at the point where I need to paint my hall but I am reluctant to do this if some of the plasterboard screws are going to show through again. Should I get the walls skim coated or if any of the screws were going to pop would they have done so by now. Also is it expensive to skim coat?P.S I did paint the bathroom ceiling and first coat the surface was fine, went to give it a second coat and one of the screws had 'popped' Am I doing something wrong with the paint?

sounds like the screws were not properly set or sealed to begin with- probley just poor workmanship. Just so ya know after the screws are put in they need to be sunk in a bit with some pressure - then sealed with mud or patch. I would guess your contractor did that already. ? and are you sure they used screws? i only ask cause sometimes nails are used and they pop causing the problems you mentioned- but the right screw is used it is uncommon that would happen. If you live in a moist area where there is high humidity - it is possible that the plasterboard has expanded a bit pushing the screws out- you can have the humidty levels checked - or you can probley feel if there is excess moisture in the room and maybe that can be cleared up with good ventilation. It is also possible they did not use a long enough screw, or the beam was not hit when it was screwed in- if thats the case then there probley is no remedy except basicly removing all the screws and repositioning them.

Q:hi i am going to put wallboard up in my girlfriends shop...i was going to use 2by 2 timber studding....but some one said you can get alliminium studding...any 1 know anything about this or any links to websites

If this is a business code states that you must use metal studs and 5/8 drywall for a fire stop.Metal studs are held together with a self tapping screw.You can buy a metal cutting blade for your saw.You will also need a self tapping screw to hang the board.

Q:Gold gypsum board

Not necessarily good gypsum board support time is long, the construction level is also very important on the one hand, if the construction is not easy to lead to cracks in the gypsum board joints. Gypsum board is divided into: glass fiber gypsum board, gypsum board, decorative gypsum board, perforated sound-absorbing gypsum board several categories. Which there are ordinary gypsum board, moisture, fire, water and so on several. Glass fiber gypsum board and no paper and paper the difference. (1) moisture-proof plaster decorative plate is particularly suitable for bathroom, kitchen decoration. (2) sound absorption gypsum board has a strong anti-noise function. (3) composite gypsum decorative board both insulation, insulation, and decorative effect. (4) paper gypsum board widely used, decorative effect, suitable for living room, the ceiling.