CB Series Car Battery Charger

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT or LC
Min Order Qty:
10 Pieces pc
Supply Capability:
10000 Pieces per Month pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

 

battery charger 

1.compact,light and portable

2.simple operat

3.reasonable price

 

 

Battery charger 

Features:

Modern design and high performance. 

Simple operations and maintenance.

Equipment with selector for normal or quick (boost) charge.

Compact, light and portable.

Provide with complete kits, equipped with ammeter.

 

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:It is not water-cooled argon arc welding machine, but the welding torch is water-cooled. Can it be connected with water cooling?
I didn't catch what you said
Q:Reallink 200 argon arc welding machine, can long time continuous welding
Can not. Load sustained rate of 200 reallink argon arc welding machine (%) is only 60%.Sincere answer, if satisfied, please accept in timeI think the questioner's question is whether he can work for a long time under rated current, rather than asking what kind of current to work continuously.And your algorithm is wrong. Reallink 200 argon arc welding machine, according to the duty rate of sixty percent, the current can be obtained through the calculation of continuous work for the 155, the output current is less than 155. The situation will continue to work.
Q:How can the ordinary invert direct current welding machine be changed into argon arc welding?
Add a high frequency arc striking and hand switch circuit and solenoid valve,
Q:Argon arc welding machine starting indicator light is not bright, fan turn is how, can not welding
Check the circuit
Q:What is the two output voltage of inverter type DC arc welding machine?
Inverter type DC arc welding machine with two output voltage of 70V;Inverter type DC arc welding machine is an arc welding machine based on MOSFET field effect power tube as switching element. First of all, the frequency of the 50Hz input voltage is rectified and filtered into DC voltage, and then through the power electronic switch into high frequency (100KHz) AC voltage, the AC voltage into AC voltage for welding process required by the transformer, the rectifier filter into DC voltage welding. The output current is controlled and regulated by the pulse width modulation control (PWM) technique. As the switch power inverter technology is adopted, the weight and the volume of the welding machine are greatly decreased, the efficiency is improved, and the energy consumption is saved.
Q:Can the invert manual welder be argon arc welding machine?
Yes, the general requirements are not high, can mainly be afraid of contact with the arc when the tungsten pollution parent material
Q:I bought a reallink brand WSE250 argon arc welding machine, manual welding of aluminum can not be too simple, better when in use
Welding aluminum material, buy AC argon arc welding machine, you buy DC argon arc welding machine, welding aluminum welding is not good,Senior welding man
Q:Common faults of DC invert manual arc welding machine
TroubleshootingThe switch power supply indicator is not on, the fan does not turn, no welding output, 1, confirm the power switch closed.2. Make sure that the input cable is connected to the power supply.Power indicator light, fan does not turn, no welding output 1, may be wrong input on the 380V power supply, causing over-voltage protection circuit start, change to 220VPower on, you can reboot.2, 220V instability (power input line or too long) or input lines overlap in the grid, resulting in over-voltage protection circuit starting, increase input line grid line diameter; the fastening input line node, this phenomenon is shut down 5-10 minutes after the restart recovery.3, a short time continuous open and close power switch, cause over-voltage protection circuit start, shutdown 5-10 minutes later, restart, you can return to normal.4. The wire between the power switch and the power board is loosened and re tightened.5 、 the 24V relay on the power board is not attracted or damaged, check the 24V power supply and relay, and the relay can be replaced by other relays of the same type.When the fan is turned and welded, the output current is unstable or not controlled by potentiometer. When the current is large, it is small 1, potentiometer 1K, and the quality is not good. Should be replaced.
Q:What are the welding electrodes and argon arc welding machines used for welding machines?
Stainless steel wire! I just do stainless steel, what do not understand, despite asking me!
Q:Two can welding machine be used as argon arc welding machine?
Can. 2 welding machine is also a DC welding machine, but the no-load voltage is higher than our general motor, very unsafe, not recommended. Argon arc welding is divided into melting pole and non melting pole (that is manual tungsten inert gas arc welding). If you choose melting pole, please use AC welder.
We enjoy good reputation at home and abroad. Our company specializes in manufacturing motors, pumps, air compressors, welders and cutters, etc. We have enjoyed high favor among the customers. In addition, we can produce motors according to the request of the customers. At the same time, we supply complete inspection of electric property and mechanical property. Your coming and choosing our products will be sincerely welcomed. We will sincerely supply best services for you.

1. Manufacturer Overview

Location Zhejiang, China (Mainland)
Year Established 1995
Annual Output Value
Main Markets North America3%
.South America3%
.Eastern Europe5%
.Southeast Asia12%
.Africa20%
.Oceania1%
Mid East30%
.Eastern Asia5%
.Western Europe5%
.Central America3%
.Northern Europe3%
Southern Europe2%
.South Asia8%
Company Certifications Certificate of Conformity;Certificate of Conformity

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size: 10,000-30,000 square meters
No. of Production Lines
Contract Manufacturing
Product Price Range