Q:What does "D41X-16" mean?

D butterfly valve, 41 flange connection, X rubber seal, 16 kg pressure

Q:Can the inlet and outlet of butterfly valve be reversed? Why? What will happen if the reverse gear is installed?

Hard seal butterfly valve in any case, the reverse loading will cause tight seal.

Q:I did a compression check on my 350 chevy. I have low compression of 175psi on one cylinder.The other seven cylinders range from 195psi to 205psi Could the valves be too tight on the cylinder with 175 psi compression?

Chev engines have hydraulic lifters, keeping the valves adjusted correctly at all times. 20 lbs isn't much to worry about anyway, but if you want dump a little oil (about a tablespoons worth) into that cylinder and recheck it. If the compression jumps up, then your rings are getting weak. If not, you may have a leaky valve.

Q:Gate valve, butterfly valve and so on can do the valve so that?

Valve can not be used to adjust the use, if the switch can not be in place, the medium flushing gate valve is easy to cause poor sealing!

Q:The water supply pipe is the gate valve And on the cross dry pipe are the gate valve? To answer the 30

1, this is a good question, it seems that this has not yet made a unified standard requirements, a bit confused2, personal understanding of fire water supply pipe, pipe shall be installed on the valve, because the valve is fully open all closed features of fire control system is usually required is fully open, easy management features are obvious.3, fire water supply system is also useful to butterfly valve, but mainly signal butterfly valve.The signal butterfly valve is generally installed in two parts: floor level, dry pipe, flow indicator front end, trunk pipe, wet alarm valve, front end.Floor level pipe installation is a function of the signal valve, when the floor spraying system needs repair, close the valve, open the end of the floor drain, emptying the water in the spray system, maintenance; two is the sprinkler system is not allowed inside water, when the butterfly is closed, will transmit a signal to the the fire alarm system, fire alarm system receives a monitoring signal (so called signal butterfly valve), fire sprinkler system that the floor is anhydrous state, fast repair.Wet alarm valve at the front of the signal butterfly valve with the main floor of the main role of the butterfly valve, first, maintenance, and two is the prompt sprinkler system, there is a signal butterfly valve closed, should be repaired as soon as possible.

Q:1st where is my zone valve? I have an old Burnham gas baseboard heater2nd What do I do?My last resort is calling a proffesional.

First: Wat make you tinkling that the zone is bad? Every zone cooperate with 2 other essential parts: thermostat and power supply, In 90% of my carea, people firs go with their thinking to zone, but only 10% was realy zone. The first thing to check is termostat and power. you could do this very simply by removing termostat wire and tickling them together several times, if they have spark, than the most prabably is just thermostat broken

Q:For whatever reason, Mazda has made it next to impossible to change the PCV valve on the 929. I'm going to have to pull off the plenum and the passenger's side valve cover to replace a $2.00 PCV valve. Before I get too involved, I need to know the torque specs for the valve cover. Also, any other tips on this process would be greatly appreciated. Can I reuse the old valve cover gasket if it's still in good shape? Should I use any kind of sealant in addition to the gasket when I put it all back together? Thanks in advance, by looking at this motor, I can tell I'll have my work cut out for me (for a friggin $2.00 PCV valve, it's usually SO simple!). Like I said, any and all help is greatly appreciated.

Mazda 929 Specs

Q:Butterfly valve in the use of the difference? Caliber?

Role of butterfly valveButterfly valve is to use disc type to open and close parts reciprocating reciprocating about 90 degrees to open, close or adjust the flow of medium valve. The butterfly valve has the advantages of simple structure, small volume, light weight, material consumption, installation of small size, the driving performance of torque is small, simple operation, rapid, high chemical corrosion, and can also have good flow control function and closure characteristics, the use of butterfly valve is very extensive. Its varieties and quantities are still expanding, and the development of high temperature, high pressure, large caliber, high sealing, long life, excellent regulation, as well as multi-function development of one valve. Its reliability and other performance indicators have reached a high level. Disadvantages, there is a certain resistance to the medium.Gate valves are more used in steam pipes and large diameter water supply pipelines, because of the general requirements of fluid resistance is small, the use of gate valve.Valve is hand wheel rotation, stem upward movement. Flow is not the same, the gate valve requires full open. Need a higher installation space, the valve sealing surface has a certain self sealing capacity, its spool by the media pressure closely with the valve seat sealing surface contact, to achieve tight leakage. Wedge gate valve spool angle is generally 3~6 degrees, when forced to shut down excessive or temperature changes of the valve core is easy to die. Therefore, high temperature and high pressure wedge gate valve, in the structure have taken certain measures to prevent spool stuck. The valve in the opening and closing valve and valve seat sealing surface contact and mutual friction is always so easy to wear sealing surface, especially in close off the valve, the valve before and after the great pressure, sealing surface wear is more serious.

Q:My caravan is a bit sluggish on the pick up, I replaced the wires/plugs and the electronic distributor(I think thats what it is..). still a bit sluggish. Should i look at the valve gasket? Or fuel filter, or fuel pump next? 03 caravan sport 3.3L

the valve pan gasket won,t cause it but the fuel filter will if it,s starting to clog up and also the cat nverter !

Q:What type of butterfly valves do you have in DN125?

125D42X: manual double eccentric flange butterfly valve 125D3 (6, 9) 42X: worm (gas, electricity) double eccentric flange butterfly valve125D41X: manual single eccentric flange butterfly valve 125D3 (6, 9) 41X: worm (gas, electricity) moving single eccentric flange butterfly valve125D43H: manual three eccentric flange butterfly valve (hard seal)125D3 (6, 9) 43H: worm (gas, electricity) move three eccentric flange butterfly valve (hard seal)125D71X manual alignment type butterfly valve125D3 (6, 9) 71X worm (gas, electricity) midline type clip butterfly valve125D3 (6, 9) 73H, worm (gas, electricity) three eccentric pair clip butterfly valve (hard seal)125BD71 (F4) X corrosion resisting fluorine (wrapped) pair clip butterfly valve