butterfly valve PN1.0-1.6MPaStandard Structure: Butterfly Pressure: Low Pressure

Ref Price:
Loading Port:
Tianjin
Payment Terms:
TT OR LC
Min Order Qty:
1 pc
Supply Capability:
9999 pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Quick Details

Standard or Nonstandard: Standard Structure: Butterfly Pressure: Low Pressure Power: Manual Material: Casting Temperature of Media: Normal Temperature Media: Water Port Size: DN40-DN1200 Place of Origin: China (Mainland) Wafer type: butterfly valve Packaging & Delivery

Packaging Details: Plactic bag+Paper cover+Plywood cases 

Delivery Detail: Within 20 days 

Specifications

Wafer type lined butterfly valve 

1.Design standard:ISO,BS,API 

2.DN40-DN1200 

3.PN10/PN16/PN25 

4.Center lined disc 



Wafer type lined butterfly valve 


 


 


Technical Data


DN40-DN1200mm PN1.0-1.6MPa


General Design:ISO 5752 / BS 5155 / API 609


Body: Cast Iron, Ductile Iron, Carbon Steel, Stainless Steel


Seat: EPDM, PTFE, NBR,Viton


Stem: Stainless Steel, Steel,


Disc: Ductile Iron with Nickel Coating,Ductile Iron with Nylon Coating, Stainless Stee 304/316l, Alu-Bronze,Duplex steel


Flange Connection:DIN,ANSI,JIS,BS


 


Product Features


Wafer type flanged body style fit between FF or RF flanges


PTFE bushing ensure the maximum shaft support and centralized alignment


360°polished disc assures positive on-off


Hard-Backed Cartridge seat or Edge-Boot seat


The pin,spline or square connection are all available


Universal ISO 5211 mounting pad.


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Tight valves?
unless they have been tampered with that wouldn't be it,they usually wont tighten up on their own,i would suspect maybe a valve with a slight burn place on it that's causing that to happen or a ring causing you to loose that much compression,try adding a small amount of oil in the cylinder and then do the compression test again,that will tell you if its a ring or a valve,that's a big loss of compression ,and when you see that much of drop its usually a burnt valve.good luck.
Q:How do you draw the butterfly valve in the engineering drawing?
There is one of the most stupid way: find a picture of the butterfly valve, insert into the CAD, and then follow the trace, and there is a lot of CAD on the network of butterfly valve, yourself down..
Q:How many kinds of butterfly valves are there?
Also known as butterfly valve, control valve has a simple structure, can be used for low pressure pipeline valve switching control is closed parts (disc or disc) is a disk, around the valve axis to achieve the opening and closing a valve, the valve can be used to control the flow of air, water, steam steam, all kinds of corrosive medium, mud, oil, metals and radioactive liquid media and other types of fluid. On the pipeline, mainly from cutting and throttling. Butterfly valve headstock is a disc shaped disc, in the valve body around its own axis of rotation, so as to achieve the purpose of opening or closing or regulation.[structure]The utility model is mainly composed of a valve body, a valve stem, a butterfly plate and a sealing ring. The valve body is cylindrical and has short axial length and is internally provided with a butterfly plate.
Q:What is a Valve Adjustment?
Not at all a big expense most places should do it for $90 -150 including the gasket . Takes me about an hour to do one. If you don't adjust them eventually you could wear the cam possibly although I've never seen any issues from not doing it. If they are too tight then possibly they could've got the engine hot . If they are too loose which is what they should do as they wear they'll just be a little noisy until you get them adjusted if I can help in any other way please let me know hope this helps
Q:How a car's performance depends on the number of valves?
the v is in reference to the motor its in a v formation v8 4 cyliders on each side v6 3 per side v12 6 pre side now the valves is how many are in each cylinder you usually have 3 or 4 valves per cylinder the more valves the more horsepower the more cylinders the bigger the engine
Q:Timing belt reason for bent valve?
If it was a timing belt issue it woudn't have only been one cylinder. And usually if it's only off by one tooth, it just runs poorly. IT has to be off by quite a bit, or the belt has to straight up break to bend a valve,, if that happened it would have made a horrible clanging noise repeatedly before it eventually sputtered out. the 1999 Si revs to what... 8000 rpms? You didn't happen to miss a shift and over-rev the engine, did you?
Q:What is the principle of butterfly valve and check valve? Any difference?
Direct water butterfly valve, check valve is to water can not flow valve
Q:Butterfly valve D41W-1, 41, W, 1, respectively, what does that mean?
This butterfly valve in our factory called butterfly, 4 represents the connection of the flange connection flange is French, 41 in 1 on behalf of butterfly valve, W represents the body seal, is C that is actually the correct type of cast steel, should be D41W-1C. Suitable for ventilation, smoke, and these media.
Q:Butterfly valve network and ordinary butterfly what is the difference?
1. The butterfly valve of the pipe network adopts an eccentric structure. When closed, it has the function of closing and tightening. The sealing performance is reliable. After opening and closing, the cover is completely sealed, and the cover is completely out of contact, so as to ensure that the sealing surface is not damaged.2, the sealing surface is made of stainless steel, corrosion resistant, high temperature resistant, long service life. With two-way sealing function, medium flow is not affected by the installation restrictions (if only one-way control medium should be used to seal the installation direction) is not affected by a single space, can be installed in the any direction.
Q:Especially butterfly valve
Butterfly valve is fully open to fully closed is usually less than 90 degrees, the opening refers to the butterfly plate rotation angle;Linear closing should be the locator is linear, if the potentiometer is 0-10 euro, corresponding to 0-90 degrees, 500 Europe, opening 45 degrees;

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range