Q:How do you draw the butterfly valve in the engineering drawing?

Butterfly valve there are many kinds of painting, according to the design institute out of the icon, below we together to understand the icon, which has the butterfly drawing.

Q:Types of butterfly valves

There are clip on butterfly valves and flanged butterfly valves,Manual, pneumatic, electric,

Q:valve adjustment 2001 chev prism 1.8L

valve adjustment . you need to know the fire order. the gage between the stem. rotators the cranshaft. it could be cold start. cylinder need to be bottomed center.

Q:What's the material of the butterfly valve seat?

The seating material shall meet the following criteria:1) fluid compatibility, including expansion, hardness loss, permeability, and degradation;2) hardness;3) permanent deformation;4) the degree of recovery after load removal;5) pull in and compressive strength;6) deformation before fracture;7) modulus of elasticity.

Q:I got my timing belt done on a 1999 Civic Si on September 26 @ 113,699 miles. at 116,9xx miles I bent a valve on my third cylinder. How likely is it that the timing belt is the reason why this happened? I heard that if the timing belt is a tooth or so off, it could bend a valve. So is it likely that this could have happened? Anyway to check?

COMPRESSION TEST OR CHECK ALL TIMING MARKS TO SEE IF THEY ARE IN ORDER

Q:What is the difference between the installation and function of a butterfly valve and butterfly valve?

The principle of the valve gate valve is open and close cases, RAM direction of motion perpendicular to the direction of the fluid, valve can only be fully open and fully closed, can not be adjusted and the throttle. Gate has two sealing surface, the most commonly used mode gate valve of the two sealing surface forming wedge, wedge angle with valve parameters vary, usually 50, medium temperature is not high when 2 degrees 52. Wedge gate valve can be made into a whole, called the rigid gate; can also be made to produce micro deformation of ram, in order to improve its process of deviation, make up the sealing surface angle in the process, the gate is called the flexible gate. Valve closed, the sealing surface can only rely on medium pressure to seal, that is to rely on medium pressure to the gate sealing surface pressure to the other side of the seat to ensure the sealing surface seal, which is self sealing. Most of the valve is forced seal, that is, when the valve closes, to rely on external force to force the gate to the seat, in order to ensure the sealing surface sealing. Gate valve with the stem along with a straight line of motion, called the lift rod gate valve is also known as the bar gate valve. Usually there is a trapezoidal thread on the lifter. The rotating motion is changed into a straight line through the nut at the top of the valve and the guide groove on the valve body. That is to say, the operating torque is changed into the operating thrust. When opening the valve, when the gate lift height is equal to 1:1 times of the valve path, the passage of the fluid is completely unblocked, but at run time, this position is unable to monitor. In actual use, the top of the stem is used as a sign, i.e., the open position, as its fully open position.Temperature changes appear to consider locking phenomenon, usually open to the vertex position, and then rewind 1/2 1 circle, as a fully open valve position.

Q:Butterfly valve is the control valve?

The flow characteristics of butterfly valves can be approximately equal percentage characteristics, with the positioner can do adjust, is mainly used in large caliber, straight stroke control valve more than 200 volume weight will be great, it suggests using the butterfly valve.

Q:Classification of telescopic butterfly valve

(1) Central sealed butterfly valve(2) single eccentric sealed coal valve;(3) double eccentric sealed butterfly valve(4) three eccentric sealed butterfly valve (1) soft sealing butterfly valve.1) the sealing pairs are made of non-metallic soft materials, which are made of non-metallic soft materials.2) the sealing pair is made of metal hard material and is made of non-metallic soft material.(2) metal hard sealing butterfly valve. The sealing pair is made of metal hard material and is made of metal hard material. (1) forced sealing butterfly valve;1) elastic sealing butterfly valve. The pressure of the valve seat, seat, or plate is produced when the seal is closed by the pressure from the valve

Q:My bike has now 6200 miles on the odometer. The manual says that a valve adjustment should be performed every 6000 miles. But the bike runs fine. Can I just have the valve checked or should I have them adjusted even though the bike is fine? What will happen if I just keep riding it?

if the valves are not chattering (WOrse then normal) and you havent lost power or gas milage, then no...dont get it adjusted and no ... your not hurting the bike.

Q:What does "C" in D971F-16C DN450 RF mean for electric butterfly valves?

C represents the valve body and the material is cast steel;D stands for butterfly valve; 9 stands for electric; 7 stands for clip type; 1 represents middle line butterfly valve; 16 stands for nominal pressure 1.6Mpa; RF stands for flange joint; in the form of protruding surface.