EMC XLPEFLEX Wind Energy Shielded Control Cable
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 m
- Supply Capability:
- 100000 m/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Product Standard:
Enterprise Standard
Application:
EMC XLPEFLEX wind energy shielded control cable is applicable for free hanging or fixed installation in fin cabin.
Type and Name
Type | Name |
EMC XLPEFLEX | EMC XLPEFLEX Wind Energy Shielded Control Cable |
Environment Conditions:
Altitude: 1000m
Ambient air temperature: Perennial mean temperature: 10℃
Extreme high temperature: 50℃
Extreme low temperature: -42℃
Average relative humidity: normal value for accumulated year: 80%
Earthquake Proof: Horizontal acceleration: 0.2g
Normal acceleration: 0.1g
Safety factor: 1.67
Note: g is acceleration of gravity. g=9.8m/s²
Extreme wind speed:30.0m/s
Range of Laying:
Cables mainly lay in the cabin of fan, where machinery oil may leak or overflow.
Operating Properties:
Rated Voltage U0/U: 300/500V
Continues operating temperature: Flexible: -5~+90℃
Fixed: -40~+90℃
Min. ambient temperature when laying: -5℃
Min. bending radius : Flexible:10d
Fixed:5d
Note: d is outer diameter.
Product Introduction
Conductor:
•Conductor should comply with the requirements for Class 5 specified in IEC60228.
•The surface of conductor should be bright and clean no grease, no burr or bulge or faulted wire to damage the insulation.
Isolated Layer:
•Every conductor coat with an isolated layer made from appropriated material.
•Insulation
The nominal value of the insulation thickness shall comply with IEC60227-7. The average value of insulation thickness should be no less than nominal value, and the thinnest part should be no less than 90% -1mm of nominal value.
Insulation adopts XLPE, whose property should comply with provisions in IEC60502-1. The insulation should be rapped on conductor tightly and easy to peel without damaging the insulation, conductor and coating. The surface of the insulation should be flat and color evenly.
Insulated conductors are separated by colors, and in accordance with DIN VDE 0293. Generally, adopted colors are brown, black, gray, yellow/green.
Shield:
The shield adopts the structure of tinned copper braid and aluminum foil lapping. The density of tinned copper braid should be no less than 90%.
Sheath:
•The nominal value of sheath thickness should comply with the requirements of GB9330, and the average value of outer sheath should be no less than nominal value. The thinnest part should be no less than 85%-0.1mm of nominal value.
•Sheath is made from PVC mixed material, whose properties should comply with requirements for PVC/ST5 specified in sheet Two of IEC60227-1. The sheath should tightly rapped on stranded insulated core or coating. Meanwhile, the outer sheath should be clean and color evenly.
•The outer diameter should comply with requirements in GB9330. The color for sheath is grey or black.
Finished Cables:
•The ohmic value of conductor should be no more than specifications in IEC60228 at 20℃.
•Finished cables and insulated cores should withstand the rated AC voltage test of 2500V, and no breakdown in five minutes.
•The resistance of insulated conductor should be no more than 20MΩ•km.
•Mechanical and physical properties for finished cable insulation should comply with IEC60502-1.
•Mechanical and physical properties for finished cable sheath should comply with IEC60227-1.
•Finished cables should withstand the burning test specified in EN50265-2-1 or IEC60332-1.
•The shield impedance for finished cable should be no more than 10Ω/km at 20 ℃.
Inspection Rules:
•Products can leave factory only after passing examination of technology department. Each package should be shipped with the product quality inspection certificate.
•Products should inspect according to GB9330. If it fails for the first time in sample inspection, then take another two samples to examine the failed project. If the two samples are acceptable, then the products are acceptable, false otherwise. The number of samples is accepted by both sides, or decided by manufacture at the time of no requirements from the buyer.
Mark、Packing、Transport and Storage
Mark:
•There should be marks of maker, type, nominal cross-section area, voltage on the cable. The marks should comply with the requirements for conductor and color specified in DIN VDE 0293-308.
•Marks shall be legible, not easy to erase. The writing should be clearly visible after 10 times graze in absorbent cotton cloth.
Packing:
•Cables can be packed both in coils and in circles. Cables in circle should be packed on cable specified in JB/T8137. Cables should be positive sealing, for those outside the circle, protective cover should be made. And the length of outside should be no more than 300mm.
•Tags should identify:
① Maker or trade-mark
② Type and specifications mm²,V
③ Lengths m
④ Manufacturing Date: Year Month
⑤ Product Standard Code
⑥ Correct direction for circles
Transport and Storage:
•The cables should avoid high temperature and cable circle does not allow flat.
•Forbid throwing circles with cable from high attitude and mechanical damage.
•Forbid lifting several circles at the same time. Circles should be put firm with appropriate methods to avoid tip over.
- Q:I know they can control networks but what about cable, what is keeping cable channels from just showing hardcore pornography 24/7even showtime has a no bottom/no thrust/no rod rule.I don't have HBO so I don't know what they use, but still do we really need the FCC to censor its obvious that tv channels aren't desperate to put porn on the air so why do we need the FCC (other the the frequency adjustments for radio and what not)
- The FCC controls what is broadcast over the air waves. Cable TV is by subscription only, so if you don't like the programming you don't subscribe. Broadcast TV requires no subscription and is freely available to anyone who turns on a TV set. If the FCC were not there to control broadcast TV you would soon see porn popping up everywhere, since it is about the only thing that sells.
- Q:Cable zc_y v22 what does it mean
- No problem with the copper, the home is no problem as if you take a twisted pair as a telephone line KVV with BV material, the process is not much difference in the production...
- Q:It wont do any damage will it?
- It really depends on the what the connector is. If it is a 8 Pin CPU cable, it is a definite no no. However, if it is a 8-pin PCIe cable, then you are safe to plug it in your GPU. However, keep in mind one rule, never force a plug into pins that do not fit.
- Q:what does the power cable that comes with video cards do? is it for when u dont have a 6-pin power connector or something? j/w cuz im thinkin bout gettin a ati 3850 and it requires a 6-pin connector, but yet i know 2 dudes with the same psu as me, runnin a ati 3850 perfectly.HP Hipro 300W 12V 19amps but yet it doesnt have a 6-pin connector
- That's right, the power cable is in case your power supply doesn't have a 6-pin power connector. A 300W power supply for a 3850 is cutting it a bit close, but you'll probably get away with it if the rest of your machine is typical. (Typical machines with a 3850 are just under 200W peak. See link.)
- Q:Okay so I am trying to upgrade my graphics card and In order ti di That I need a new Power Supply Unit. The PSU I was looking at is a 850 watt one and it has six pin connectors. The problem is all my componets are 4 pin connectors. If I get the new power supply can I somehow get a 6 pin connector to fit in a four pin like a adapter or something. BTW in order for the graphics card to function I need a six pin but all my other stuff in 4. So is there a way to work that out
- exchange the PSU, for a extra powerful one. 430W @80percentefficiency = 344W 500W @80percentefficiency = 400W 600W @80percentefficiency = 480W 650W @80percentefficiency = 520W 700W @80percentefficiency = 560W 750W @80percentefficiency = 600W 800W @80percentefficiency = 640W 850W @80percentefficiency = 680W 900W @80percentefficiency = 720W 950W @80percentefficiency = 760W 1000W @80percentefficiency = 800W minimum PSU 700W-800W.
- Q:if i remove the power cable and switch on it works normally without restarting , plz help with this ~?
- go in control panel and set ur laptop settings to not to start while swith in
- Q:i would like to have my power cables and control boxes inside in one spot is this possible? if so how and how expensive would it be?
- You could use trunking for the cables, and for the control boxes if they are in the house you could hide them under a box which you could decorate to look like a parcel...personally I would paint it, but drill some holes for ventilation.
- Q:10KV cable is directly from the nearest substation led to the power distribution room, how some people say that from the transformer can not understand what the meaning of more
- Low-voltage power cable, also known as: low-voltage power cable. The voltage rating is 0.6 / 1KV. National Standard No .: GB / T-2008. The voltage rating of the control cable is 450 / 750V. National Standard No .: GB / T9330-2008. The voltage rating of these two cables, the country has a clear standard. Can not be changed.
- Q:Did not find the relevant norms. Fiber optic cable should not be affected by interference, electric corrosion this piece without taking into account? More
- My computer --- right-click properties. Device Manager. Look at the USB device is not there or the number. Have to reinstall the system. Also make sure your motherboard USB interface is not good. I said the interface is plug USE jumper of the root.
- Q:How many amphs does the us ps3 slim's power cable have? It should be #A?
- i don't know why youre trying to find this out but heres a chart. The power cable has different electricity usages depending on what youre doing but the average is 87 ish
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
EMC XLPEFLEX Wind Energy Shielded Control Cable
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 m
- Supply Capability:
- 100000 m/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products