Q:What is the size and length of the DN80 gate valve? 10 kg and 16 kg, respectively?

Valve structure length standards are PN16, short series for 203mm, long series for 280mm, flange size by PN16.

Q:Internal screw current limiting gate valve (Tan Gang) PN5.0 DN15/ Phi 1 Rc1/2 what does that mean?

We did thatInternal thread current limiting gate valve (Tan Gang)Body material: carbon steelPressure rating: PN5.0 = 300LB American StandardNominal = DN15 = 1/2"Phi 1 = in the middle of the gate drilling a Phi 1 hole, so that in closing there will be a certain flow, that is, the minimum flow, that is, the current limit.Rc1/2 is thread, which is the connection

Q:Will the water supply and drainage to wear civil air defense gate valve, the use of bright rod or dark rod?

3, soft sealing rubber lining valve plate size uniform, interchangeable. Therefore, the soft sealing gate valve will be the direction of development, but also the water supply industry is willing to adopt a valve.

Q:Installation and operation instructions of knife gate valve

5., when installing the valve, users must reserve the necessary space for valve actuation;The wiring of the 6. driving device shall be carried out according to the wiring diagram;7. knife gate valve must be regularly maintained, shall not be arbitrarily collision and extrusion, so as not to affect the seal.

Q:Acid resistant alkali valve gate valve

D is small in shape and beautiful in appearance.E operation is simple and labor-saving.

Q:What do you mean by gate valve type RVHX-0150-10 and Z45X-16Q?

Z45x-16q, Z means gate valve, 4 means flange connection, 5 refers to dark rod gate valve, X means rubber seal, 16 refers to nominal pressure 1.6MpaRVHX means manual gate valve, 150 refers to the caliber of DN150, and 10 indicates nominal pressure of 1.0MPa

Q:What else, P54140V, 170V? What do they mean?

P work pressureP54 temperature at 540 degrees of work pressureThe pressure at P54 100 is 540 at the temperature of 100barV valve for chromium molybdenum vanadium steelP54 pressure 140V temperature at 540 DEG C for 140bar valve for chromium molybdenum vanadium steelP54 pressure 170V temperature at 540 DEG C for 170bar valve for chromium molybdenum vanadium steelFrom the JB/T4018 "valve type model preparation method"The standard unit is MPa, but it is usually used in bar

Q:What is an inverted seal gate valve?

It refers to the middle part of the valve sealing valve valve sealing surface, the valve cover has a sealing seat, which is the valve and stem as well as the joint of the valve rod and the valve cover (i.e. internal stuffing box at the bottom of a sealing structure).

Q:What is the difference between gate valve Z41T and Z45T?

Z41T is a dark pole gate valve, and Z45T is a plain rod gate valve,

Q:The legend of gate valve and stop valve

The working principle is different. The stop valve is an upward stem type, and the handwheel rotates and rises with the stem. Valve is hand wheel rotation, stem upward movement. Flow is not the same, the gate valve requires full open, the cut-off valve is not the same. The gate valve has no inlet and outlet direction requirements, and the cut-off valve has the required inlet and outlet!Gate valve and stop valve are shut-off valve, is the most common two valves.From the exterior, the gate valve is shorter than the cut-off valve, especially the bar valve needs a higher height space. Valve sealing surface has a certain degree of self sealing capacity, its spool depends on the media pressure tight contact with the valve seat sealing surface, to achieve tight leakage. Wedge gate valve spool angle is generally 3~6 degrees, when forced to shut down excessive or temperature changes of the valve core is easy to die. Therefore, high temperature and high pressure wedge gate valve, in the structure have taken certain measures to prevent spool stuck. The valve in the opening and closing valve and valve seat sealing surface contact and mutual friction is always so easy to wear sealing surface, especially in close off the valve, the valve before and after the great pressure, sealing surface wear is more serious.