Most Efficient Heating System

Hot Products

Air Flowing Linear Air Diffusers China Supplying

1-4 way curved blade air vent linear diffusers air flow vent air conditioning

3 way curved blade air diffusers ceiling use

3 way Stractly Square Air Diffusers Vent for HVAC Systerm

Air Diffusers Air Flow Vent for Ceiling

Rectangle Air Grilles Air Flow Vent for Air Conditioning

Square Air Diffusers Air Flow Vent for HVAC Systerm

Square air Vent Diffusers for Air Conditioning

linear bar ceiling air diffuser for air fresh

Air diffusers air flow vent for HVAC systerm America Market

FAQ

Geothermal coil spacing is too hot not how to do

The spacing is too large to increase the water supply temperature (& lt; 60 degrees), or to accelerate the hot water cycle

Radiator parallel system how to take pictures

The installation of the radiator is divided into two forms: the installation and installation of the radiator. The installation steps include the installation of the pipe, the installation of the radiator, the installation of the boiler, the pressure test and the customer acceptance. Trouble, need to slot and install the set of water, for the decoration of the housing, the general choice to install the radiator, installed both convenient and not damage the indoor decoration effect. 1. Laying the pipeline in advance with the customer to communicate with the location of the radiator after the installation of the need for the layout of the pipeline, the pipeline is generally in the ceiling, baseboard and other hidden places, the laying of the tube as much as possible not to affect To the interior decoration or take up too much space. 2. Install the radiator in the process of installing the radiator to the radiator to be stable, and to use the level of measurement to see if the installation is smooth, and then the valve connection and inlet and outlet valves connected, after checking the correct The pipe clamp is reinforced. 3. Installation of the wall-mounted boiler The installation of the boiler should be noted that with the open line and electrical equipment separated from the flammable and explosive materials can not be on the hair to promote the safety of the body, Table and gas stove should be more than 300mm distance. 4. Stress test and customer acceptance Construction workers in the pipe stamping test when there is no run, run, drain, drop and other phenomena, confirmed by the customer after the inspection can be accepted.

How to choose the wall heater

There is no difference between the use of the boiler and the radiator. Mainly to choose the brand, good reputation of the dealer, and experienced installation staff.

Solar water heater mixing valve pressure balance

You can choose a thermostatic valve

Which brand is good to warm the mixer?

This, it does not matter. As long as the big brands, are similar, mainly to see the above water pump, the valve to make the skin can be used to avoid the anti-Jiu Xue single grinding and temperature parts of the pros and cons. It is recognized that the better pump is Grundfos (Denmark).

What is the difference between the hydraulic module and the original hydraulic module? Please master as much as possible to say the details?

Energy-saving air-conditioned room is in the original ordinary air-conditioning room structure, the traditional room of the pump, the valve group, filter decontamination equipment, energy-saving equipment, supporting parts and control systems of these components together. Used in warm air conditioning water system in the water medium power transmission and control and connect the host and the heat transfer end of the pipeline, in series to form a standardized equipment. Equipment through the professional staff according to the real shortage of speculation in the past, the need to match the various components to the most economical and energy-saving program customization

PE-RTII Oxygen-resistant heating tube custom specifications manufacturers where?

The installation of the warm pipe in the use of metal components to meet, such as switch valves and other metal knot bones buried in the body of the machine, in the plastic pipe during the hot water cycle of these metal parts can easily be corroded, which Will be detrimental to the long-term use of the floor heating system. But the warm system is for a long time to use, and its parts are difficult to replace, which caused the use of heating system inconvenience. Why is hot water circulation in plastic pipes accelerating corrosion of metal parts? After a foreign expert survey concluded that: because the pipe after heating oxygen more easily penetrate the plastic pipe into the hot water, resulting in corrosion of metal parts. Oxygen infiltration is a slow effect, but the corrosion of parts is indeed very obvious, while the heating system is limited to the maintenance and replacement of inconvenient parts, so the impact is not as simple as imagined. Heating plastic pipe is highly resistant to corrosion and high temperature resistance, other materials are difficult to replace, and even if it is possible to replace the metal may not be the role of corrosion, so the key issue is how to solve the oxygen permeation. After research and testing, some foreign experts found that an oxygen-resistant plastic pipe can effectively solve this problem. As the name implies, the oxygen barrier has a good barrier to oxygen permeation, which will greatly reduce the corrosion rate of metal parts. The result of using it is that the average life of the warm system can often be extended, usually over 10 years.

Is not to warm the total valve opened on the line, do not control the room valve

If you automatically control the system, open the total valve will not control. If not, where the need for heating to open the corresponding area of the valve, where do not need to turn off the corresponding performance of the following. When running, the total access to the water ball valve have to open.