Clear Duct Hose

Hot Products

FAQ

I hate the plastic tubes. They're fiddly awkward to use, especially as they get near running out. Metal was SOOO much easier. Just roll up the tube it stays rolled up. Just squeeze the metal it doesn't pop right up as soon as you release the pressure, but stays down. Basically metal packaging was right for the job. Plastic tubes are a poor, inadequate alternative, I hate them.It can't be due to cost, since so many drinks are still sold in metal cans, if it was down to the cost all the metal cans would be replaced with cheaper plastic alternatives, but they're not.So what is the reason it's only plastic for toothpaste now?
It is due to cost. Drinks used to be sold in steel cans and glass bottles, now they are sold in aluminum cans and plastic bottles, due to cost. You can buy a plastic clip to put on the toothpaste tube to solve your problem.
I live in Mississauga, and I was wondering if there were any places close by even in Toronto that sell neon plastic test tubes, for drinking purposes/partying. Would the dollar store provide that sort of stuff, or do I have to order that online?
www.okorder
does it matter where you pur the fluid and how much should be poured in my vanhave a radiator caop and then like a long plastic tube that goes down to the engine and says coolant on it...where do i pour the antifreeze??
Fill-up the plastic container The plastic container that connects to your radiator is the extra fluid. The level of fluid in that container will rise and lower as the heat of the fluid changes, but should be at the full mark when your car has not been running. If you are loosing fluid due to a leak and it gets too low fill it up with water. Radiator Coolant is used particularly in places were its cold, because its much harder to freeze. But if you run out, your car could over heat.
What is the transition metal pipe between the plastic water supply pipe and the water heater?
The transition piece is a combination of plastic and metal, and the two materials are processed by injection molding process, and the anti leakage sealing is realized through the internal structure without adding other adhesive materials.
So I was eating GoGurt yogurt. And I think I accidentally swallowed a part or the jagged part on the top of the tube. I don't think it was very big. I'm guessing the size was the size of half of a dime or a 1/4 of a dime. I know this doesn't sound too bad, since I've heard people who swallowed pennies, then they were fine, but I don't know how to get rid of it. I can still breathe and drink normally, but when I talk for too long, my throat starts to hurt a little. So far, I've tried drinking lots of water, swallowing some food to push it down (rice. :D), coughing, vomiting, and clearing my throat but I think it's still there. I'm actually not sure if it's still there or if it is gone, or just made a cut so it hurts. But I don't want to go to the doctors or ER, I'm poor. Are there any other ways to get the plastic out? Oh and if I leave it there, how long will it take for it to go down my throat and digest?
Try eating more rice. If that doesn't work try to stick your finger down your throat but not far enough to make you throw up. Try to pull it out. I did that once when I was choking on a cheeto. Good luck
How to remove dirt on the inner wall of plastic pipe?
In the first bowl upside down water, tap water can, do not need too much, and probably can usually wash water, then pour 84 disinfectant, and then put for a while, with a rubber glove hand cloth wipe dirt in the basin, can easily fix.
The cast iron pipe is broken. Replace it with PVC. How do I change it?
Cast iron down pipe connection with PVC pipe:1, at the interface congestion, leakage, seal, (building materials stores have sold)2, with a PVC big head, variable diameter, iron pipe inserted inside the variable diameter;
Plastic tube how to link three links?
If it is PPR pipe, you can only call outside the master of water and electricity, should be PPR water pipe joints need welding machine, very troublesome.