Q:How does the pneumatic butterfly valve control the angle of opening?

This is really not good, control seems to be pneumatic defects, can only rely on the feeling

Q:How to control the single acting pneumatic butterfly valve?

Single acting pneumatic butterfly valve can be divided into gas open type and gas closed type, which is usually called "normally closed" and "normally open". This is very critical. The single feature pneumatic butterfly valve is the biggest feature of its spring reset function, when the loss of gas or sudden failure, you can automatically restore the original state. So it's important to open the air or air this time.

Q:The flow ratio of area and maximum flow area of the valve is? If it refers to the opening of the valve rotation angle? Butterfly linear closure refers to the butterfly valve at constant angular velocity close? When the change trend of flow is what? These valves problem bothering me for a long time,

Butterfly valve is fully open to fully closed is usually less than 90 degrees, the opening refers to the butterfly plate rotation angle;Linear closing should be the locator is linear, if the potentiometer is 0-10 euro, corresponding to 0-90 degrees, 500 Europe, opening 45 degrees;

Q:I HAVE A 2003 FORD EXPEDTION THAT IS IDLE ROUGH,AND WILL EVENTUALLY STALL. TODAY I FOLLOWED THE PCV VALVE HOSE TO THE BACK OF THE THROTTLE BODY AND NOTICED THERE IS A BIG HOLE ON THE ELBOW OF THE HOSE. HOW CAN I CHANGE IT? CAN I JUST FORCE THE HOSE OUT AND SIMPLY PUT A NEW ONE? BEEN HAVING THIS ROUGH IDLE /STALL PROBLEM FOR A WHILE I CLEANED IAC VALVE, THROTTLE BODY CHANGED THE AIR FILTER AND ALSO CLEANED THE MASS AIR FLOW SENSOR, I HAVE A P0171 system to lean(bank 1) code

So, the rubber elbow hose has a hole in it. Your best bet is to get the replacement from the Ford dealer. Yes, you can buy just the elbow part from the parts counter at the dealer. If they start acting all dumb (and won't help you or sell you the part) then, go to a different dealer for the part. Another thing you could try is a used one from the junk yard BUT, it's been my experience that the rubber gets too hard and the PCV valve needs a lot of encouragement to be removed. Sometimes you'll damage the used elbow by trying to get it off of the engine or removing the old PCV valve to put in your replacement valve. That's why I recommend getting a new one straight from the source. They are pretty simple to change with ordinary hand tools and some mechanical know-how. You just pull the elbow off of the port that it's attached to on the engine. The valve will probably have a steel clip that goes around the hose at one end of the valve inside of the hose. You simply squeeze the clip with a pair of pliers and tug at the valve until it comes out of the elbow.

Q:That industry uses most of the butterfly valve, and only use the butterfly valve, a large number of use of butterfly valve, seek expert advice!

I know there are automatic fire fighting systems and the oil industry.

Q:Where are the exhaust valves, mud valves and butterfly valves?

The exhaust valve is suitable for the pipeline with working medium, so as to improve the efficiency of the water conveyance equipment and protect the pipe from deformation and rupture. Sludge discharge valves are suitable for use in floating waste water treatment plants, such as gypsum. Slag, scale power stations, smelters, sugar mills.

Q:can't locate freon intake valve for 03 jaguar an was wondering were it is located at

If it has one it should be located on the smaller line near the AC compressor.

Q:Transformer butterfly valve and pressure relief valve difference

I don't know. Let's have a Baidu! Baidu is powerful.

Q:How big is the butterfly valve with a diameter of 80?

With the 80 caliber butterfly valve.Also known as butterfly valve, control valve has a simple structure, can be used for low pressure pipeline valve switching control is closed parts (disc or disc) is a disk, around the valve axis to achieve the opening and closing a valve, the valve can be used to control the flow of air, water, steam steam, all kinds of corrosive medium, mud, oil, metals and radioactive liquid media and other types of fluid.

Q:16 inches below the choice of electromagnetic valve can be the same, it turned out to be DN200 election 1/4, and now there are DN350 can also use this? With it, limiter, pressure relief valve, locator model will change?

DN200 pick 1/4DN350, DN400 corresponding solenoid valve, you can choose 3/8 hose 12mmOther accessories are related to valve path and pressure. If the same series, the valve has no change at all.