Solar Monocrystalline Panel Series (90W-100W)

Ref Price:
$0.54 - 0.65 / watt
Loading Port:
Shanghai
Payment Terms:
TT or LC
Min Order Qty:
5000 watt
Supply Capability:
40000000 watt/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Solar Monocrystalline  Series (90W-100W) l : High efficiency crystalline solar cell. Even if under the weak light, the solar module can produce maximum power output.

II Tempered glass (toughened glass): Anti-reflecting coating and high transmission rate glass increase the power output and mechanical strength of solar module.

III EVA and TPT: Using high quality EVA and TPT to prevent destroying and water.

IV AI frame: Without screw, rner connection. 6 holes on the frame can be installed easily.

V Junction box: Multi function junction box with water proof.

VI Long lifetime: ≥25 years; Less power decrease.

VII Good performance of preventing from atrocious weather such as wind and hails.

VIII Resisting moisture and etching effectively, not effected by geology.

 

Standard Test Conditions of Solar Monocrystalline  Series :

The opto-electrical specifications shown below are stabilized values being measured at Standard Test Conditions, Irradiance: 1000W/m2, Spectrum: AM1.5 at 25°C, The info below is subject to manufacturing tolerances. Where appropriate minutes of measurement are available and are used for the dimensioning of the installation.

 

Advantages of Monocrystalline Silicon Solar Panel

• CNBM Solar performance guarantees for 25 years

• 12 years guarantee for workmanship

• Timeliness of delivery

 

Specification of Solar Monocrystalline  Series

- Optimal permutation on solar cells to keep enough heat diffusion, decreases hot spot effect.
- High quality and anti-ageing EVA, weather resistance backside raw materials assure reliable solar panels.
- Passed 5400Pa mechanical loads testing by UL, can withstand bad and high mechanical load working environment.
- With good sealed performance, moisture resistant, aging resistance, high/low temperature resistant, the inner terminals of our junction box owns good electrical performance transmission. Bypass diodes used can avoide hot spot effect and damages to panels. Output cables and mating connectors are safe and reliable for installation application. Adopt weather resistance, sealed, good sticky silica gel when assembling.
- Strict quality inspection on each procedure and 100% electrical performance test to meet power requirements.
- 0~+3% power tolerance.
- classification for all the panels in order to improve the integral performance of system and solar panel life span.
- TUV、UL、MCS、CE、ROHS、Golden Sun certified
- Underwriting of 25years output power warranty by The People's Insurance Company of China.

 

 

Characteristics

Max Power Voltage Vmp (V)

17.4V

17.6V

17.8V

Max Power Current Imp (A)

5.33A

5.62A

5.79A

Open Circuit Voltage Voc (V)

22.2V

22.3V

22.4V

Short Circuit Current Isc (A)

5.17A

5.40A

5.62A

Max Power Pm (W)

90W

95W

100W

Temperature Coefficient of Cells

NOCT

47℃±2℃

Temperature Coefficients of Isc (%/℃)

+0.06%

Temperature Coefficients of Voc (%/℃)

-0.33%

Temperature Coefficients of Pmp (%/℃)

-0.45%

Mechanical Data

Type of Cells(mm)

mono125×125

Dimension

1190×550×30mm

Weight

8kg

NO. of Cells and Connections

4x9=36

The dimension of the modules can be changed according to the demand of clients

Limits

Operating Temperature

–45 °C to +80°C

Storage Temperature

–45 °C to +80°C

Max System Voltage

700V

Guarantee

Products Guarantee

2 yrs free from defects in materials and workmanship

Performance Guarantee

No less than 90% within 10yrs and no less than 80% within 20yrs

Certificates

IEC, ISO, TUV, CE

 

Solar Monocrystalline Panel  Series (90W-100W)

Solar Monocrystalline Panel  Series (90W-100W)

Solar Monocrystalline Panel  Series (90W-100W)

 

FAQ

We have organized several common questions for our clients,may help you sincerely:

①What price for each watt?

It depends on the quantity, delivery date and payment terms,

②What is your size for each module? Can you tell me the Parameter of your module?

We have different series of panels in different output, both c-Si and a-Si. Please take the specification sheet for your reference.

③Can you provide the peripheral products of the solar panels, such as the battery, controller, and inverter? If so, can you tell me how do they match each other?

Yes, we can, we have two companies for solar region, one is CNBM International, the other is CNBM engineering Co.

We can provide you not only the solar module but also the off grid solar system, we can also provide you service with on grid plant.

④What is your warranty system?

 Our product  performance guarantees for 25 years

• 12 years guarantee for workmanship

• Timeliness of delivery

• Quality Products certified (TÜV, UL, CE, ISO)

⑤How do you pack your products?

We have rich experience on how to pack the panels to make sure the safety on shipment when it arrives at the destination.

⑥ Can you do OEM for us?

Yes, we can.

⑦How long can we receive the product after purchase?

In the purchase of product within three working days, We will arrange the factory delivery as soon as possible. The pecific time of receiving is related to the state and position of customers.Commonly 7 to 10 working days can be served.

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Chem question regarding using solar panels ....?
It is not that simple. There are 3 main types of solar cells. Monocrystalline silicon is the most efficient and produces the smallest solar cells, and therefore the smallest panels. Poly-crystalline (or multi-crystalline) silicon produces the next most efficient type of cells and are a popular choice. Amorphous (or thin-film) silicon uses the least amount of silicon and also produces the least efficient solar cells. This means thin film system take up more area than the other two; an important factor to consider in relation to possible future upgrades; i.e. if you'll have enough space left to do so. The North (in the Southern hemisphere) or South (in the Northern hemisphere) facing roof collects the most energy. So this biases the roof area required. Your energy usage can be changed. Hot water (a major energy user) could be better using direct solar heating with peak demand boosting, either from mains or solar. There are other possibilities, either to reduce demand or to provide energy from other sources. Not all sunshine hours are equal. Hours around midday are far more productive than hours later in the day. This must be factored in.
Q:solar panels and batteries?
If it pulls 9 amps continuously, that's 08 watts/hour or about 2.5 kwh/day. If it only pulls half that (does it cycle?) it's about .2 kwh/day. You only want to drain a lead-acid battery 50% or so, so you'll want a 5 or 2.5 kwh battery pack. A typical setup for the 5 kwh would be two L-6 batteries in series, and for the 2.5 kwh you could use 2 T-05 batteries in series. This does not account for days of cloud. If you regularly have cloudy days, size the battery pack for two or three days of use with no input (2-3 x the sizes given above). To charge them, you typically want panels that will charge your battery at least 5% of its capacity per hour (C/20). For 2 volt nominal panels that's 0 amps for the T-05 or 20 amps for the L-6 batteries. It's good to have more than that for battery life (it cuts down on what's called stratification), so you'll want probably 50-200 watts of panels for the T-05 and 300-400 for the L-6. You'll also need a charge controller. Peltier coolers are very inefficient. You'll save money by using a regular mini-fridge and an inverter. Most mini-fridges only draw 50 watts or so, so you're talking 600 watt-hours for a 50% duty cycle. This means two T-05 batteries will give you two days of use and you'll only need 20-50 watts of panel. DK
Q:Solar Panels!!???!!!?
Solar Power. There is no denying it, solar power works. Not only is it energy efficient, it is also safe and extremely clean. Whether it may be for a home, business or a community, there are no limits to the energy that the best solar panels are able to offer.It is a guarantee that once this medium is applied, you would easily slash your greenhouse gas emissions and electricity bill.
Q:Solar panels IRS refunds?
Not a good answer: CNBC had a news bit, that it can take 0 to 20 years for you to break even in energy costs after installing solar panels. Please don't buy them just for the tax deduction. See if you can google a calculator for this - do research. I have a brother in law that buys anything under the sun just because he gets a tax deduction. I'm sure you're not like that though. Run the numbers of what you will save vs the 2K you will spend You may never break even
Q:Adding Solar Panels to my home in Portland, Oregon?
As per the question, the answer is no. Solar panels are available, they are expensive, they can reduce your energy bill, you can get up to 30% of the expense back from your taxes, but they must be installed by a qualified electrician or solar panel installer to work properly.
Q:Can you overload solar panels with too much light?
Solar panels have a upper temperature limit, and it's only a bit more than it would reach in a very bright sunny day near the equator. Start shining heat lamps on it and you will raise it past it's max temperature, and it will die. .
Q:Are solar Panels worth it?
“Where you have good (sunlight) and access to financing and a combination of federal and state incentives, you have a number of markets around the country that are very vibrant, and it’s very cost-effective with financial paybacks in the order of five and 0 years,” said Robert Margolis, a senior energy analyst at National Renewable Energy Laboratory (NREL).
Q:What do I need to do to run my dehumidifier from solar panels?
Solar Powered Dehumidifier
Q:How Do Solar Panels Work?
The most important parts of a solar cell are the semiconductor layers, this is where the electron current is created. There are a number of different materials available for making these semiconducting layers, and each has benefits and drawbacks. Unfortunately, there is no one ideal material for all types of cells and applications. In addition to the semiconducting materials, solar cells consist of a top metallic grid or other electrical contact to collect electrons from the semiconductor and transfer them to the external load, and a back contact layer to complete the electrical circuit. Then, on top of the complete cell is typically a glass cover or other type of transparent encapsulant to seal the cell and keep weather out, and a antireflective coating to keep the cell from reflecting the light back away from the cell. A typical solar cell consists of a cover glass, a anti-reflective layer, a front contact to allow the electrons to enter a circuit and a back contact to allow them to complete the circuit, and the semiconductor layers where the electrons begin to complete there voyages! The solar panels, in order to generate power, are using the method of screen-printing, a technique developed for printing fabrics, paper and to produce plastic, glass and metal solar cells. The basic materials of a photovoltaic cell (solar cell) are inexpensive. The homemade solar cells have about /4 of the efficiency of commercial silicon solar cells, which turn 0-20 per cent of light energy into electricity. But, being cheap to produce, they can make up the loss in quantity what they lack in quality.
Q:Solar Panel, what is the catch ?
Read the terms and conditions! They will own the panel and receive payment for any power generated from it, as one example.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range