Q:What are the specific steps of stirring the steel ladle castable?

Steps are as follows. 1 Compulsory mixer is used to stir the castable and bags, rope and other debris can not mix in the castable when stirred. 2, Castable should be unpacked on the scene. Stirred volume depends on the capacity of the mixer. Castable should be accurately measured and put into a blender. 3 The process of first dry mixing and then wet mixing is adopted. After the castable is added to the mixer, it is dryly mixed for 2 minutes, add about 5.2 to 5.5 percent of water and continue to add water while stirring. Water that is 80% of the total should be added, and then decide whether to continue to add or not depending on the consistence (noting that the water must be clean water and sewage can not be used). Then it is wetly mixed for 4 minutes and stirred for not less than 6 minutes at one time, until castable is even. In general, the bottom is slightly dry and the wall of the ladle is slightly dilute (the amount of water is only for reference). 4, The amount of water and mixing time should be controlled strictly when stirred to ensure that the needs of the consistency are met. If castable is too thin, it will seriously affect the quality of the material. The stirred volume, stirring time and water that is added should be consistent and they can not suddenly be thick or suddenly be thin. If the consistency does not meet the requirements, the castable should be put back to the mixer and stirred with appropriate water or dry materials. 5, It should be stirred evenly and casting should finish in 20 minutes, in order to avoid sclerosis, affecting structural strength of ladle lining 6, After each completion of construction, varieties of castable should be changed and the mixer should be cleaned 7, Stirring can stop in halfway. If the mixer breaks down and it can be repaired in a short time, some of the materials have to be removed before the machine is opened. If the machine can be repaired on time, castable refractory should all be removed.

Q:Who knows about the B-level fireproof insulation materials?

Organics, extruded sheet, polyphenyl board and phenolic resin. The fireproof?performance of sea capacity module (fireproof and thermal insulation material) is B1-level with the heat conductivity coefficient of only 0.028w / m · k. It is a good choice. A-level: Rock wool, glass wool, silicate, aluminum silicate, calcium silicate, phenolic aldehyde, and foam glass. B-level: Rubber and plastic, extrusion molding, polyphenyl, PEF.

Q:A chemical problem with refractory materials

In chemistry, there is never absolute

Q:What's the requirements of fire-fighting criteria of heat insulating material?

Specific provisions go as the following article 8: roof grassroots adopted duration of fire resistance is the non-combustible component that shouldn't less than 1.00 h's. Its roof insulation materials should not be below B2; Otherwise, the combustion performance of insulating material should not be below the B1 level. Article 9: The junction of the roof and wall, the insulation layer around the opening part of roof should use the grade A thermal insulation material to set level fire-fighting belt that width is not less than 500 mm. Article 10: the roof waterproof membrane or flammable insulation layer should adopt incombustible material to cover.

Q:What are the differences between first-level fire-resistant materials and second-level fire-resistant materials?

The combustion performance of materials could be divided into: A( noninflammability), B1(flame retardancy), B2(flammability), B3(inflammability). Building materials are divided into four ranks according to these properties. 1. In accordance with Code for Design of Building Fire Protection(GBJ16-1987)(revised edition in 2001), fire hazards in producing and storage can be divided into five types. In Fire Prevention Code of Petrol Chemical Enterprise Design(GB50160--1992)(revised edition in 1999), classification of fire hazards is also achieved according to the hazards of materials that have been using, producing and storing. Measures in prevention of fire explosion could be taken from the perspectives of fire separation, fire resistance level of structures, allowable floors, safe evacuation, and fire extinguishing facilities based on different levels of fire hazards. 2. Four fire resistance rating of buildings are listed in the book Code for Design of Building Fire Protection. And specific stipulations are made to the fire resistance of main elements of buildings, such as bearing walls, beams,pillars, and floors. When designing a building, if permitted, refractory materials of high-rank should be adopted in those buildings which have high potential fire hazard and a lot of combustible material and valuable equipment. While making sure fire resistance rating, the duration of fire resistance of each elements should meet its requirements.

Q:What's the B grade fireproofing material?

Grade B: rubber and plastic, extrusion molding, polyphenyl, PEF. organics, extruded sheet, polyphenyl board, phenolic resin. Hairong modules (thermal insulating and fireproof material) can reach grade B1 in fireproof performance.

Q:What are Grade-A waterproof inorganic thermal insulation materials?

1. Foam ceramic insulation board Foam ceramic insulation board is made of inorganic ceramic material by high temperature baking and is called ceramic insulation plate for short. 2. Composite cement foaming insulation board With cement, fly-ash and micro-silica, composite cement foaming insulation board is a kind of hole-closed lightweight hydrophobic insulation board made by foaming, maintenance,cuttign and processing. 3. Aerated concrete panel Using lightweight material, silicious material and foaming agent and so on, aerated concrete panel is a lightweight concrete panel made by high pressure steaming. 4. Rock wool board With natural igneous rock as material and thermosetting resin as binder, rock wool board is a panel made by melting in high temperature through centrifugation. I hope it can help you.

Q:How long is the fire-fighting time of A class fire resisting window?

Duration of fire resistance of A class fire resisting window is not less than 1.2 hours; B class window is not less than 0.9 hours. And when install fire window, you must use Level to correct or use hanging line method to correct verticality of four directions, making its same horizontally anf vertically. Window frame must be integrated with the building, using wooden or metal parts connected to the wall. After steel frame is installed, cement mortar must be watered between window frame and wall , and is maintained more than 24 hours before normal use.

Q:How can refractory materials be divided?

Refractory materials in China can be roughly divided into refractory products and unshaped refractories.

Q:What kind of materials are needed to make refractory bricks?

Fubang Decoration of Anhui province help you with the question: According to requirements, there are different materials, acid refractory material, such as silica bricks; neutral refractory material, such as high alumina brick; and basic refractory material such as magnesia brick.