Repeatered Submarine Optical Fiber Cable

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Product Type: LW, LWP, SAL, SA, DAL, DA type
Single-segment Length: 150km
Core Quantity: 12, 24, 32, etc
Features: suitable for optical transmission systems with an ultra-long-distance,

high-speed, water depth of 8000 m
(1) Central Tube Armored Structure
(2) Central Tuber Cable Core Armored Inside Armored Outside

Product Model: LW/4-2SM-R
Stainless steel tube optical fiber unit, high-intensity swaney steel wire

armored inside (tight-fit-type) , feeding copper conductor, high density polyethylene sheath.

Product Model: LWP/4-2SM-R
Stainless steel tube optical fiber unit, high-intensity swaney steel wire armored i

nside (tight-fit-type), feeding copper conductor, insulating layer, protective steel strip,

high density polyethylene sheath.

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:electric power cable outside?
I do not know the codes or regulations in Chicago but i do know in most states it against the law to have power lines resting on a structure. Those two lines resting on the garage could be the cable and phone company's and that is not against the law. However you could call the phone company and cable company and ask them to move them for you. If you can make a valid point that those lines are causing you harm or disturbing you in anyway possible then the company's will have to move it. And for the power cables there is probably nothing you can do unless it is really resting on your garage. But they will just tighten the line and not actually move it.
Q:Can any1 help me I have lost my power cable and adaptor for my hp printer scanner, where will i get 1 ?
Start with the model number of the scanner and find a power supply. Carl
Q:where does the main power cable go on a 50 panasonic viera TV?
It's in the back, near the main power switch but it's up and under. Look from the bottom up and you should see it
Q:Where can I get a power cable for an HP mini 1000 netbook?
polish okorder.com/ all apartments have printers regards
Q:calculation for cable sizing between 300AH battery and 200A power plant?
The battery and power plant statistics do not enter into the calculations. I assume that the load is continuous, and the battery is to be continuously trickle charged. The power plant will have to deliver the load current and battery trickle charging current, at the voltage necessary to charge the battery. You will need to know the load current, the trickle charge current, the distance between the power supply and the battery (or load if you connect directly to it), and the voltage necessary to supply the load and trickle charge the battery. The voltage drop will be the total current multiplied by the total circuit resistance. this resistance will be the sum of the individual conductor resistances. As an equation, this is Voltage drop = total resistance times current in amperes. The total resistance will be the voltage drop divided by the current. Now you know how much resistance you can stand. The National Electrical Code in the US has tables showing the resistances of various sizes of wire, and how much current they are rated to carry. From these, or maybe from you wire supplier, you can find out what size wire you need. It will need to be large enough to supply the voltage and current, and have a rating for at least that much current.
Q:Need to find a spare hole in my ford c-max 2010 mod to run my power cable for my amp?
In most vehicles there are spare holes filled with rubber plugs. Pop one out with a screwdriver and make a hole in plug a little smaller than the size of the wire for a very tight fit. If it's a smaller size power wire, it can sometimes be run through the same grommet as the vehicles main harness. Be very careful not hurt the existing wire. I have seen people get careless and screw the harness up and it's not easy or cheap to fix. When doing this I usually use a stiff wire (a small diameter yet long screwdriver can work too) and slide it through the grommet. I then use electrical tape to secure the power wire to stiff wire and pull it through. Make sure your penetration point is still leak proof after doing this. You may need to use some silicone and or electrical tape to seal it up.
Q:Is it safe to plug in desktop PC power cables without an adapter?
It all comes down to the amount of output that the pc is set to take. I would think that you would be fine without the adapter, assuming it already works. If you do decide to do this make sure you set up a surge protector, dont just plug it into the wall. A power surge could fry the internals and brick the pc.
Q:power cables and amp question.?
no sir it will not, infact it may completly stop the problem, i would say to much current is passing through the wire, if the amp will accept the wire (even if its a tight fit) thats what your looking for. so to answer your question using the 680 watt wiring kit is just what you need and will be perfect, you could even get the 1200 watt wiring kit if need be, (assumikng you bought the schosche kit from walmart)
Q:Acoustic Audio 10 inch home theatre powered subwoofer use speaker wire or subwoofer cable?
Use a long RCA cable. If you use speaker wire - you have to run wires from the left/right outputs to the sub, then more wire from the sub to the left/right speakers. Then you have to tell your receiver your left/right speakers are LARGE and you do not have a sub to get things to work. A single long RCA cable is simpler. You can even make your own with pre-terminated CATV coax and some F-to-RCA-Male adapters from Radio Shack. Subwoofer signals work fine and do not need any kind of higher end RCA cable.
Q:How to connect power cables back to the motherboard?
If your talking about the power cables from the power supply to the motherboard those are fairly straight forward. It is a 20 or, 24 pin connector. Usually along the edge opposite the external connections for the motherboard. Although, the placement really depends on the manufacturer and, could even be near the middle of the board. They are keyed and, you can not plug them in incorrectly. As long as you don't force them into the slot. If your speaking of the wires from the case to the motherboard that is a little more difficult. P3 and, P4 motherboards usually have a keyed connection that simply plugs in. Other boards have markings on each of the wires corresponding with it's connection. The one thing that is the same for every board is that the two black wires must be side by side. If you've never done it before you should have labeled each wire and, made a diagram of their placement. Your best hope short of taking your computer to the local shop is to try and, find diagrams for both your motherboard and, the case.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range