PVC/SPVC/TPE/TPV/TPO/TPU sealing strip extrusion machine / door gasket frame production line
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 10 set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
PVC/SPVC/TPE/TPV/TPO/TPU sealing strip extrusion machine / door gasket frame production line
Soft Pvc sealing strip extrusion machine
1-Raw material:Soft PVC
2-Diameter of the screw:65mm
The whole plant are composed of extruder, water cooling tank, hauling machine, double roller and coordinated with different specification of moulds to produce soft PVC sealing strips for aluminum door and windows to instead of the rubber strips.
Complete production line:
1- Automatic material dryer and feeder SLJ-400
2-Extruder
Model:LXSJ-65/28
Diameter of screw: φ65mm
Capacity:70-80kgs/h
L:D: 28:1
Material of the screw: 38CrMoALA with nitrogen treatment
HV:>800
Material of the barrel: 38CrMoALA nitrogen treatment
HV:>800
Power of motor:22kw
Inverter: FUJI
Element: TE and OMRON
Material of heater: ceramic heater
Material: Best stainless steel
3-Water cooling tank
Length:4 meters
Material: Stainless steel
Adjustment distance:500mm
Adjustment direction: three-dimensional
4-Hauling machine
Length of clamp:500mm
Width of clamp:120mm
Adjustment distance:500mm
Clamping: By pneumatic
Speed: 0.6-6m/min
Power of motor:1.1kw
Inverter: FUJI
5-Double roller (easy to operate)
6-Air compressor
7-Crusher
8-Moulds
- Q: Basic parameters of extruder screw
- 3, compression ratio epsilon, also known as the geometric compression ratio of screw, is the ratio of the volume of the first screw groove to the volume of the last screw groove at the homogenization section. It is determined by the physical compression ratio of plastics - that is, the density of the product and the density of the performance of the feed. The extruder is relatively compressed, the purpose is to make granular plastics fully plasticized and compacted. The selection of compression ratio should be different when different kinds of processing plastics are used. According to the compression ratio, the types of screw can be divided into three types: equidistant, unequal depth, equal depth, unequal distance, unequal depth, unequal distance. Among them, equidistant and unequal depth is the most common one. This kind of screw is easy to process, the contact area of plastic and cylinder is large, and the effect of heat transfer is good.
- Q: Why is the connection between the extruder and the switchboard?. The upper and lower three terminals are short circuited
- The action should be to require three simultaneous electricalOr a two way backup
- Q: Cable extrusion machine 6.57090 machine model how to see, know the master to say, thank you
- Screw diameterAskDo you mean the plastic screw? 90 machines are so long. What's the 90 machine? Thank youChasing the answerDiameter, not length
- Q: Produce 10 square wires with the smallest extruder
- If the production of single core line, then 50 machines can also do, but low efficiency, unstable line,.70 or 90 machine idealIf it is a production sheath line, do at least 70 machines, preferably 70 or 90 insulation, and 90/120 as sheath
- Q: PVC extrusion machine extrusion stone floor no pressure, what reason?
- PvC stone floor extruder pressure is adjusted by the screw and die head
- Q: Which type of inverter is suitable for extruding machine? Please give expert advice, and G series is discontinued
- They can see it moving.God doesn't need itSometimes you hear, fifth hand material,Cool sounds in the swirling smokeCoagulation together, I have left their land,Yesterday was a similar experience, ha ha
- Q: Why single screw extruder is controlled by high school and low?
- I feel like I didn't explain the problem
- Q: Wire and cable extrusion machine extrusion die how to quickly adjust the core degree, how can I touch it by hand?,
- It depends on experience, and the lines made by squeezing it are solid. When you make the line, you can see the expansion and skewness of the material!
- Q: How to adjust the 65 screw gap in the extruder?
- This should be practical learning. The outlet plane of the barrel is about 3 mm in diameter.
- Q: How many roots are produced in an hour for an PVC tube extruder?
- It depends on the type of your extruder and the specification of the tube you produced
Send your message to us
PVC/SPVC/TPE/TPV/TPO/TPU sealing strip extrusion machine / door gasket frame production line
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 10 set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
