Product Description:
Index analysis of Low Chrome Alloyed Cast Grinding Ball for CIS and Russia Made in Shandong China
Product | Brand | DIA | hardness | Breakage ratio of ball | Impact fatigue life of ball | Numbers time | Metallographic organization |
Special high chrome casting iron ball | Cr26 | 15-150MM | ≥58 | 0.5% | 6 | 15000 | M+C |
Special high chrome casting iron ball | Cr20 | 15-150MM | ≥58 | 0.5% | 6 | 15000 | M+C |
Special high chrome casting iron ball | Cr15 | 15-150MM | ≥58 | 0.5% | 5 | 15000 | M+C |
High chrome casting iron ball | Cr12 | 15-150MM | ≥58 | 0.5% | 4 | 15000 | M+C |
High chrome casting iron ball | Cr8 | 15-150MM | ≥58 | 0.5% | 3 | 15000 | M+C |
Middle chrome casting iron ball | Cr5 | 15-150MM | ≥47 | 0.5% | 2 | 12000 | P+C |
Low chrome casting iron ball | Cr2 | 15-150MM | ≥45 | 0.5% | 1 | 12000 | P+C |
Casting ball | QTB | 15-150MM | ≥50 | 0.5% | - | 12000 | - |
Casting ball | QTM | 15-150MM | ≥52 | 0.5% | - | 12000 | - |
Chemical composition of Low Chrome Alloyed Cast Grinding Ball for CIS and Russia Made in Shandong China
Item | C | Cr | Si | Mn | S | P | Cu | Mo | Ni | Hardness |
Element | 0.6-1.2% | ≤ 1.0 | 0.15-0.6 | 0.6-1.5 | ≤ 0.04 | ≤0.04 | ≤0.1 | ≤0.25 | ≤0.1 | 55-65 |
Applied Field of Low Chrome Alloyed Cast Grinding Ball for CIS and Russia Made in Shandong China
1) Power Plant, 2) Mineral Processing, 3) Refractory Factory, 4) Cement Plant
Packing Information of Low Chrome Alloyed Cast Grinding Ball for CIS and Russia Made in Shandong China
Container Bags: 1000Kgs/Container Bag
Steel Drums: 850Kgs/Drum
- Q:What is the difference between forging parts and casting parts?
- The casting parts are low in cost and short in production period. Because the molten iron has good flow properties, complex shapes can be formed. But because there may be sand holes, pores, shrinkage holes and other defects, the quality is unstable, easy to produce many defects, mechanical properties are not forged well, thus affecting the service life.
- Q:Casting pieces of plastic processing requirements can not fall off the skin,
- Usually after rusting,Did you peel it?If it isNeed to do film processingIf notPlease look for the coating factoryBetter paint (such as epoxy ester, etc.)
- Q:How to judge whether the casting is qualified?
- According to different casting process and parts materials, each has relevant standards, can be found online;
- Q:Shandong foundry, casting small pieces of precision casting
- Small foundry in Shandong too much, like many of us in Qingdao, then Dongying Changshun investment casting is a home, they are also casting precision casting equipment, specifically what I recommend that local enterprises, far is not convenient,
- Q:Lathe processing stainless steel casting parts to use what type of tool, the speed into the amount of how much tool angle
- What kind of work, what kind of material, 204201304316, how big live ah? You ask?Can the 201 pieces of material and 304 of the pieces fit in a single car? Can I use the universal YG8 knife? Straight, knife, pipe thread?You should live to say, understand, say, do not understand, draw a simple drawing with Baidu doodle, marking the important size, this is good to answer ah!
- Q:How to get rid of casting sand inside casting parts?
- Are you saying that in the sand casting cavity? We use the manual blast, he is like a pipe will be automatic shot out of the grit, into the casting cavity, to remove the internal cavity in the purpose of casting sand!
- Q:How do casting parts remove stress?
- Annealing treatment, according to different casting annealing treatment, eliminate thermal stress, if need to restore hardness or increase hardness, and then quenching treatment
- Q:Where is the difference in performance between the rolled and cast parts of the same part?
- uch as: automobile transmission shaft adopts mechanical rolling machine with good performance, gray cast iron can play seismic effect effectively, with good thermal conductivity of radiator graphite in gray cast iron, the aircraft engine turbine blade by casting directional solidification casting and Dan Jingzhu.Do everything we can to make the best use of it, the advantages and disadvantages of rolling and casting, and you'll find it yourself, Baidu, depending on how you use it
- Q:Why do casting parts have air holes?
- Cangshan Qiao hidden his answer is quite comprehensive, you can try using inert gas to reduce air cover
- Q:When there is no flaw detection for large casting parts, is there any crack inside?
- According to the industry standards, within the scope of the standard requirements to determine whether the product is qualified
Grinding King are leading manufacturer and professional exporter of grinding media balls in China.with the annual output of 50,000 to 70,000 metric tons.Our products grinding media balls are mainly exported to more than 20 countries and regions in the world, such as Japan,Korea,Africa,Zambia,Malaysia,Phillipines,Indonesia,Mongolia,Australia,UAE,Chile etc.
1. Manufacturer Overview |
| Location |
Shandong, China |
| Year Established |
2000 |
| Annual Output Value |
Above US$100 Million |
| Main Markets |
Africa; Mid East;South Asia;Southeast Asia;Eastern Asia;Southern Europe |
| Company Certifications |
ISO9001;IS014001 Certificate |
2. Manufacturer Certificates |
| a) Certification Name |
|
| Range |
|
| Reference |
|
| Validity Period |
|
3. Manufacturer Capability |
| a)Trade Capacity |
|
| Nearest Port |
Qingdao Port; Tianjin Port; Shanghai Port |
| Export Percentage |
|
| No.of Employees in Trade Department |
6-10 People |
| Language Spoken: |
English；Chinese； |
| b)Factory Information |
|
| Factory Size: |
Above 40,000 square meters |
| No. of Production Lines |
Above 10 |
| Contract Manufacturing |
Grinding Ball; Grinding Rod; Cylpeb; Grinding Media; Ball Mill Ball |
| Product Price Range |
Average |
