Q:What brand of carbide is used in woodworking tools?

Carbide YS2T: is used for low speed roughing and milling of heat resistant alloys and semi finishing of titanium alloys, stainless steels, and low alloy steels. Carbide YL10.2: has high flexural strength and good wear resistance, used in low speed rough car and milling heat-resistant alloy, titanium alloy, also can be processed glass fiber reinforced plastic, making PCB micro drilling and so on. YG3/YG6: is suitable for hard alloy cast iron, nonferrous metals and their alloys and non metallic materials during continuous cutting fine cars, semi refined car, suitable for small section iron fine car, and can be used for the coarse thread, steel, nonferrous metals, wet lubrication tensile alloy wire and non metal wire drilling etc..

Q:Is there any pollution in the production of cemented carbide?

The main pollutants in the production of cemented carbide are dust, waste residue and waste water, and the biggest influence on the environment is soot. According to regulations, waste gas can be divided into two categories: particulate matter, exhaust gas and gaseous pollutants. The exhaust gas of ferroalloy plant comes from ore smelting furnace, refining electric furnace, roasting rotary kiln, multi layer mechanical baking furnace and aluminum metal smelting furnace. Ferroalloy plant exhaust emissions, dust concentration is high, 90% of exhaust gas is silicon dioxide, but also contains chlorine, nitrogen oxides, carbon monoxide, sulfur dioxide and so on. Waste residue and waste water are the most serious pollution of chromium compounds, and there are also pollution of nickel compounds.The State Economic and Trade Commission, the State Environmental Protection Administration and other departments also jointly issued "on accelerating the restructuring of China's ferroalloy industry views" (in the economic and trade industry [1999]633), from 1999 to 2005, to stop the new types of ferroalloy electric furnace (kiln) and blast furnace.

Q:What materials are hard alloys used to process?

YG hard alloy, impact resistance, high temperature resistant, processing pig iron.

Q:What are the cemented carbides?

For example, YT15, which represents average TiC=15%, is tungsten carbide cobalt carbide with the remainder of tungsten carbide and cobalt content.Tungsten, titanium, tantalum (niobium) carbidesTIC cutterIs the main component of tungsten carbide, titanium carbide, tantalum carbide (or niobium carbide) and cobalt. This kind of hard alloy is also called universal cemented carbide or universal hard alloy.The grade by "YW" ("hard", "million" Pinyin prefix) and sequence number, such as YW1.

Q:The welding welding hard alloy cutter, should use what type of flame why

With the fire on it. Put the knife and put some red hot and then put up with borax alloy outer flame burning red and then placed in a good point copper alloy and borax on the use of knife gap flow with upper and lower outer flame burnt gap can be

Q:Can hard alloy be welded with silver electrode?

Hard alloy can use silver electrode welding, some more liquid silver wire than general tin brass or iron brass, the cost is too high, the strength level than the ordinary copper electrode should be higher, personal suggestions for the selection of copper base up instead of silver electrode, such as the WEWELDING 46 electrode (referred to as Odin Wei 46 If the strength of electrodes), the structure is higher than silver, if it is to achieve the high permeability, it is still the ideal to silver, only from the strength level, is not WEWELDING 46 copper based electrode.

Q:The difference between carbide knife and white steel knife

5, the scope of application is not the same: the general tool materials used carbide, complex difficult to shape, or require very sharp, high toughness and other field applicable high-speed steel

Q:What does WC refer to in cemented carbides?

Refers to: tungsten carbide powder, is the main raw material for the production of cemented carbide, chemical formula WC. Full name: tungsten carbide powder is black, six square crystal, has metallic luster, hardness is similar to diamond, it is good conductor of electricity and heat.

Q:Can ceramic tools process cemented carbides?

Specific to the needs of carbide processing brand to determine,Cemented carbide, such as tungsten carbide, can be machined with a CBN toolReference: "CBN tools for processing hard alloy material, Valin super hard"

Q:What kind of cemented carbide is the most wearable?

As for what kind of carbide is the most wear-resistant, in fact, mainly depends on the use of conditions, the most wear-resistant carbide materials may be more brittle, so it may not be able to use. Under the same conditions, generally speaking, the tungsten particles smaller, higher hardness, higher wear resistance. If you come up with some materials to choose from, you can choose it. Domestic materials, for exampleYG3>YG6>YG8>YG15>YG20. Imported materials are more detailed, there are V series, K series, and so on.