Hydraulic Rubber Hose DIN EN 857 2SC DN12

Ref Price:
Loading Port:
Tianjin
Payment Terms:
TT OR LC
Min Order Qty:
500 m
Supply Capability:
80000 m/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

DNHose I.DHose O.DWorking PressureBurst PressureMinimum Bend RadiusWeightLength
inchmmmmMPaPsiMPaPsimmkg/mmetres
61/46.414.245652518026100750.2850/100
85/167.916.040580016023200850.3650/100
103/89.518.337.5543815021750900.4150/100
131/212.721.5314495124179801300.5950/100
165/815.924.7304350120174001700.6350/100
193/419.028.628.74162115166752000.8050/100
25125.436.622.5326390130502501.1750

DIN EN 857 2SC Standard
Tube : Oil resistant synthetic rubber
Reinforceent : two high tensile steel wire layers 2 w
Cover : Abrasion and weather resistant synthetic rubber
Temperature range : -40 ℃ to +100 ℃。

 

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What is the principle of communicating devices? What if the rubber tube is used as a connecting device to change the water for the fish?
The principle of communicating devices can be explained by liquid pressure. If the same liquid is contained in a U glass tube, a small liquid AB is conceived at the center of the bottom of the communicating device. If the liquid is stationary, it does not flow. The pressure of the liquid in the left tube toward the right side of the liquid AB must be equal to the pressure of the liquid in the right tube toward the left of the liquid AB. Because in the communicating vessel is filled with a liquid, the same two liquid column density, according to the formula of P= P GH liquid pressure that only when both sides is equal to the height of liquid column, the liquid column is equal to the pressure on both sides of the liquid film AB. Therefore, in the case of no flow of liquid, the liquid level in each vessel of the communicating device shall be kept flat. (ideal model method) the connecting device is characterized in that the liquid level in each container is flat only when the same liquid is contained in the container. If the container is tilted, the liquid in each container is about to begin to flow. One end of the liquid column flows to the lower end of the liquid column and stops flowing until the liquid level in each container is normal. As with rubber tube two glass tubes connected together in container with a liquid, which will be a fixed tube, the other tube up and down or tilt, can see the two tube level in stationary phase remained flat. The connecting device is provided with the same liquid, but the pressure on the liquid surface is unequal, and the pressure difference of the liquid surface is equal to the pressure difference produced by the liquid level difference of the two container of the communicating device.
Q:Will the outside of the brake hose of the car burst apart?
There is a potential safety hazard to the outside rubber skin. It is possible to slam on the brake. The brakes are not trivial, so I suggest you replace them in time.
Q:What are the properties of stainless steel metal hose materials?
Stainless steel metal hose material is generally 304 stainless steel, the material of good ductility, flexibility, corrosion resistance, high temperature resistance.
Q:Will the electric water heater be well connected with metal hose or hose?
On the other hand, the utility model can effectively avoid the frequent switch of the water heater power switch because of the two grounding. Therefore, the metal pipe connection does not meet the safety and installation specifications.
Q:Hydraulic quick change joint (external thread) how to connect and seal with hose? Do you need a transition joint?
As for hydraulic joints, they don't need other aprons to seal them, and the product itself is concave, and it is convex at one end, so it can be completely sealed after connecting.
Q:What are the matters that should be paid attention to when installing rubber hose joint in water pump?
Installation notes: 1, Shanghai rubber pipe joint non super displacement limit at the time of installation; , 2 installation bolts to be symmetric, gradually tightening pressure, to prevent local leakage; 3, flat, suspended, vertical installation of rubber pipe joint, actual axial displacement pressure rubber tube joints should be smaller than the pipe support, otherwise should install anti pull off device to prevent work pressure; 4, rubber pipe joints should be away from heat, ozone, no strong radiation light. Exposure and use of media that do not meet the requirements of the product; 5, rubber pipe joint in the transportation, loading and unloading, installation, no sharp instruments across the surface of the sealing surface;
Q:What is the difference between plastic lined steel pipe and rubber lined steel pipe?
Service life: because the lining rubber tube generally uses the rubber board to carry on the internal bonding, therefore inevitably has the union seam, but the lining plastic tube is a molding. Therefore, in the general chemical water transportation and Xunhua water treatment, the lining pipe is more stable, and the service life will be longer. But in the condition of the abrasive medium, the lining hose will be more durable.
Q:How can the tightness of rubber tube and metal pipe joint be ensured?
See how much your pipe diameter, diameter is around 10%, the metal pipe is inserted into the 2-3 rubber tube diameters, almost, don't worry, coupled with a hose clamp.
Q:Standard for implementation of type KXT-1 rubber joints
It is divided into 3 kinds: flange type, fixed flange type and thread type by connection. The structure can be divided into 5 kinds: single sphere, double sphere, different diameter body, bent sphere and wind pressure coil. A tubular rubber component is composed of inner and outer layers of rubber, cord and steel ring, which is vulcanized and molded and then combined with a metal flange or a parallel joint.
Q:Can the natural gas hose not exceed 1.5 meters or 2 meters?
The gas hose on the principle of not more than 1.2 meters, and regularly check the technical requirements, 1-2 must be replaced if the temporary gas can also be longer, if long-term use, as far as possible the use of metal pipe joint and the gas stove can also use metal hose, high safety factor.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range