HOT MELT PRESSURE SENSITIVE ADHESIVE
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- 20000 m²/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
CONSTRUCTION:
Synthetic Rubber,Tackifying Resin and other Auxiliaries
TYPICAL PHYSICAL PROPERTIES:
Appearance: Translucent and yellow blocksolid
Ring-and-ball softening point: 80±5℃
Brookfield Melting Viscosity: (cps/.125℃)……… 16000
150℃ ……… 9000
175℃ ……… 2500
InitialTack: ≤1cm
HoldingPower: ≥5h
180°Peel Adhesion: ≥20/in
Recommended Operation Temperature:140-160℃
PACKING:
Placed in carton, 5kg per block, 15kgper carton.
Application:
Widely used for courierbag sealing, bubble pack sealing, kraft paper bag sealing, auto tyre, shoes orthread gluing and others.
Storage:
Stored in dry ventilatedplace without direct sunlight. Valid date
REMARKS:
1. The data above are typical results and subject to change withoutnotice.
2. It isessential, that the surface to which the adhesive is applied must be clean,dry, and free of grease and oil.
3. The users should take test and dotrial-application on the above products before coming into application so as towitness and ensure suitability for their special purpose and technique.
- Q:The action of various ingredients in rubber formula
- Cost system: filler, compatibilizer
- Q:How do you remove the rubber on your new slippers?
- Bamboo charcoal (carbon fired bamboo) can purify the air and remove odors. I think the rubber should also be effective for slippers!
- Q:Is carbon black and conductive carbon black used in rubber?
- Conductive carbon black is a kind of carbon black used in rubber. After adding rubber, it can make the rubber which has not poured electricity have conductivity characteristics, but the resistivity is higher, and it can't be used as conductor for current load
- Q:How to identify the tire rubber is raw or cooked
- Rubber molding, after pressing, the elastic body is within the cohesion can not be eliminated, the molding die, often have a very unstable contraction (rubber shrinkage due to rubber vary), required after a period of time, and can be stable. Therefore, when a rubber product design at the beginning, regardless of formula or mold, it is necessary to carefully calculate the coordination, if not, it is easy to produce product size instability, resulting in lower quality products.
- Q:What is the cause of the bursting of rubber products and how should they be improved?
- There are five reasons for the bursting of rubber products: 1. forming temperature is too high, or the temperature of the upper and lower template is inconsistent. 2. the exhaust line is too open or exhaust time is too late. 3., the material quickly cooked. 4., the mold structure is irrational, there is no running trough. 5., down weight, overweight.
- Q:How does rubber mobile phone cover change yellow?
- In physical properties, rubber has swelling, rheological properties and other changes. Tensile strength, elongation at break, impact strength, flexural strength, compression ratio and elasticity decrease.
- Q:What's wrong with rubber whitening?
- Rubber whitening (spray cream) the main reason for analysis, rubber spray cream, including rubber surface spray and surface spray cream. Spray (Bloom) is a phenomenon in which liquid or solid agents migrate from rubber to rubber surfaces [1]. It can be seen that the inner compound of rubber will precipitate and form a spray. There are three kinds of forms of rubber spray. Powder spraying, wax injection, injection (also known as exudation).1. powder is a curing agent, accelerator, activator, antioxidant and filler powder with precipitation agent on the rubber surface, and form a layer of powder.2. spray wax is paraffin wax, ceresin wax precipitation etc. on the rubber surface, forming a layer of wax.3. fuel injection is softening agent, tackifier, lubricants, plasticizers and other additives in liquid precipitation of the rubber surface, and form a layer of oil.In practice, frost forms on rubber surfaces sometimes appear in one form, sometimes in two or three forms.
- Q:Rubber and metal have to be sealed before they are too strong
- Different materials and O-ring O-ring compression the change of general material such as NBR, NR, nitrile rubber, natural rubber, chloroprene rubber CR, EPDM three EPDM, HNBR hydrogenated nitrile rubber, silica gel SILICOME SBR Buna, styrene butadiene rubber, SBR, acrylate rubber ACM, compression O-ring or the 20% to calculate. If it is a special material FKM, VITON, PU, FLS silicon fluorine rubber, fluorine rubber, polyurethane, compression of these materials is calculated by 15% o ring.
- Q:PVC conveyor belts and rubber belts differ from each other in their respective advantages
- Rubber belts are widely used in conveying equipment, but do you know that proper vulcanization of rubber can maintain high elasticity of rubber and make rubber of a certain strength?. At the same time, in order to increase product hardness, strength, wear resistance and tear resistance, while adding inert filler in the process (such as Zinc Oxide, clay, chalk and barite etc.) and reinforcing filler (such as carbon black), which helps to improve the quality of the conveyor belt.
- Q:The difference between plastic rubbers and rubber boots.
- The most essential difference between plastics and rubber is plastic deformation when plastic deformation occurs, while rubber is an elastic deformation. In other words, it's not easy to restore the original state after plastic deformation, and rubber is relatively easy. Plastic elasticity is very small, usually less than 100%, while rubber can reach 1000% or more. Most of the plastic molding process is completed, the product process will be completed; and after the rubber forming process, but also need vulcanization process.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
HOT MELT PRESSURE SENSITIVE ADHESIVE
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- 20000 m²/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords