• Heavy Galvanized Wire 2.5mm  For Making Chainlink Fencing System 1
  • Heavy Galvanized Wire 2.5mm  For Making Chainlink Fencing System 2
Heavy Galvanized Wire 2.5mm  For Making Chainlink Fencing

Heavy Galvanized Wire 2.5mm For Making Chainlink Fencing

Ref Price:
get latest price
Loading Port:
Tianjin
Payment Terms:
TT OR LC
Min Order Qty:
5 m.t.
Supply Capability:
1500 m.t./month

Add to My Favorites

Follow us:


OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

Hot Dip Galvanized Steel Wire

(1) Quality : Meet GB/T 343 standard and other requirements of relevant standards .

(2) Zinc Coating: Meet GB/T 15393 standard and other requirements of relevant standards .

(3) Raw Material : Wire rod ——1006 , 1008 , 1018 , Q195 , etc, and zinc with 99.995% purity.

(4) Tensile Strength Range

Size (mm)

Tensile Strength (mpa)

0.15-1.60

290-550

0.65-1.60

400-550

1.61-6.00

400-1200

(5) Application : Used in wire mesh , artware , metal hose , binding for agriculture and construction , etc.

(6) Packing

Size (mm)

Coil Size

Spool Packing

Big Coil Packing

ID (mm)

OD (mm)

0.15-0.26

6 inch

1-14kg/spool

0.27-0.60

8 inch

1-100kg/spool

0.61-1.60

12/14/16 inch

1-100kg/spool

250-400

400-770

1.61-6.00

14-500kg/spool

450

800

508

840


 

 

 

 

 

 

Q:like in movies how do you connect like some wire to start the car? also which wires? I'm curious not trying to take anyone's car.
Connect wire 'A' to wire 'B'...Briefly touch wire 'C' to wire 'D' (until engine starts) see figure 1. Disclaimer: These instructions are not to be used for illegal purposes...
Q:I have a duplex box and want to put two recepticles in it. Each have two connector post on each side. How do I wire this.
Just wire in jumpers from the existing outlet, white wire to the silver screws, black wire to the gold screws, and unshielded wire to the green ground screw . Be sure to kill the power before you start.
Q:Ceiling light junction box has 2 wires (black and white on both). One of the two is hot (always juiced). The other of the two travels down the wall to the switch junction box, and this is the only wire in this junction box. When I connect the two blacks and the two whites of the ceiling junction box, the switch wires become juiced. But when I try to hook up a switch to those switch wires, the switch doesn't cut the power to the ceiling junction box when I flip the switch on and off. Why?? -very frustrated.
You need 2 wires going to the switch. You have the black wire from your power source on the bottom screw of the switch and another wire going to your fixture. They should both be black. If it is a white wire then paint it black at both ends. Connect the real black wire to the black on the fixture and the painted black wire to the black in the ceiling and connect both whites. You had nothing there to break the connection.
Q:if a wire of initial length, and radius has a measured resistance of 1.0 ohms. the wire is drawn under tensile stress to a new uniform radius of 0.25r. what is the new resistance of the wire?
assume the volume of the wire is constant cross sectional area = pi*R^2 A1 = PI * r^2 A2= PI * (.25*r)^2 = PI * .0625*(r)^2 = 16* A2 If volume stays constant, Length2 = 16* Length1 since resistance is proportional to length/area R2/R1= L2L1*A1/A2=16*16 = 256 The resistance now 256 times as great
Q:I need a wiring diagram for a 1983 honda rebel, its a 250cc parallel twin, i really need the ignition wiring diagram but i can't seem to find one. If anyone knows the letters (xx250,xx125) then that would help to. Thank you in advance.
Not to be rude, but that bike only has about 4 wires. What do you need to know?
Q:Is high quality CAT-5 ok to wire surround sound speakers to the receiver?
Do not use cat5 wiring. Yes it will transmit the sound but the wires gage is too small. It is also solid core wiring. Solidcore wiring is not the best for speakers. Use a good quality oxygen free copper speaker cable around 16 gage up to 50 ft. If you have 100 watts/channel or more you should use a 14 gage wire. If you are over 150watts/channel use 12 gage. Remember the wire gets bigger as the gage goes lower.12 gage wire is thicker then 18 gage wire. I personally like the Moster XP brand of speaker cable. it is not that expensive. Sometimes moster cable can be overpriced but not so much in the case of this wire. It is very flexible and will layout nice on the floor. I have purchased wire in the past that was similarly priced and it was garbage. The 20% rule stated above is indeed whack as I would have been spending $2,400 on speaker cables. NOT GONNA HAPPEN. About a $1 to $2 per foot is resonable. You will get a more than adequate wire for that price. That is about what the Monster XP cable I use costs. But copper is expensive now so the cost may be higher.
Q:A thin wire connected to a light bulb will have the bulb shine dimmer than a thicker wire. What is the scientific reasoning for this?
Thin wires are usually used to make heat because there is more resistance going through a thin wire. In an incandesent bulb 60% OF THE OUTPUT IS HEAT. If thee is thicker wire, more electrons go through and the light can be brighter.
Q:I've been meaning to find floral wire for a DIY project I'm going to attempt. Does anyone know where to buy floral wire? I'm not sure if Michael's sells it. Please let me know from personal experiences.
This Site Might Help You. RE: Where to buy floral wire? I've been meaning to find floral wire for a DIY project I'm going to attempt. Does anyone know where to buy floral wire? I'm not sure if Michael's sells it. Please let me know from personal experiences.
Q:I am replacing an outside floodlight, the cable from the house has 4 wires (black, brown, grey and yellow), but the floodlight has the standard 3 live, neutral and earth fitting. How would I wire the new floodlight.. the wiring for the old floodlight is less than a year old on a house rewire.Thanks!
Four wire power cables used to be used for 2 and 3 phase power. You would normally provide floodlight power with the use of 3 wires. How long is the cable length from house to floodlights? I would look to see what your source wire colors are and try to match those. It used to be in the USA that the red wire was used to carry the 120/240 Volts AC (50 ~ 60~ Herz). The Black wire was considered the return or negative line; and if you have a green wire it is used to put an earth ground on all the shielding, metal jackets, etc.
Q:While updating the parents basement we needed to replace a very very old 3 way switch. However, the wiring to the Fluorescents seems extreme to me. Here is how i can describle the layout. Panel - junction box - double splice (one to light fixture and one to threeway switch below it)-. From that threeway switch 12-3 wiring to upstairs landing with other threeway switch resides. How should I make my connections to switches? If the other swtiches were not so old I would just copy them.
A hot wire from the panel to the first three way switch on the common screw. Two runner wires between the two switches on the other two screws. A wire from the common screw on the second switch to the hot wire on the light fixtures. A neutral wire to the light fixtures from the panel. Look at Bert's pictures.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range

Send your message to us

This is not what you are looking for? Post Buying Request

Similar products

New products

Hot products


Related keywords