Hand Stacker--SFHXX16-A Double-Acting Pump

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT OR LC
Min Order Qty:
1 unit
Supply Capability:
1 unit/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

PRODUCT NAME:Hand Stacker--SFHXX16-A
PRODUCT INTRO

Hand Stacker
Double-Acting Pump

It’s design and small turning radius makes it easier to make sharp turns.
Controllable direction handle
Has a dual pump for easier lifting.
Conforms to EN1757-1
Top quality hydraulic pump & cylinder
Protection device for steering wheel & safety guard for load roller

 

1KG=2.2LB 1INCH=25.4MM

Model

SFH0516-ASFH1016-ASFH1016-CSFH1516-A

Capacity Q

Kg500100010001500

Load center c

mm 600600400600

Fork length l

mm 115011508001150

Fork Width b5

mm 560560255~800560

Lifting height h3

mm1600160016001600

Minimum turning radius wa

mm1540159014001590

Lifting speed

mm/sec≥20 ≥20≥20≥16

Lowering speed

mm/secAdjustable

Overall length l1

mm1650165012801650

Overall width b1

mm630680840690

Overall height h1

mm1970202020202070

Outer dia. Of the front wheel

mm80808080

Outer dia. Of the rear wheel

mm150150210150

Net Weight

Kg160223220150

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:When the hydraulic platform drops, it feels very shaken and unbalanced. Please answer?
Can you adjust the flow rate to slow down the same amount of pressure and the decrease is much faster than the increase. This does not know that the valve is connected to the solenoid valve, which may be the overflow valve or the balance valve The oil tank has no refueling mouth and oil outlet?
Q:There are different kinds of milling machine and vertical lifting machine milling machine
Start by figuring out the difference between vertical and horizontal The main shaft of vertical milling machine is perpendicular to the workbench, and the spindle of horizontal milling machine is parallel to the workbench. The knife of vertical milling machine is relatively flexible, the scope is wider. Can use vertical milling cutter, machine clip, bit etc. Milling keyway, milling plane, boring hole, etc.
Q:Hydraulic platform repair work instruction book, trouble which big man helps to provide
Remove and disassemble the descending valve, blow the plunger through compressed air and then load and resettle. Remove the hydraulic oil, tighten the connector and remove the oil strainer and clean it with compressed air, then put it back in the tank and connect the line. Do not use old oil for new oil
Q:How does the elevator repair
Professional personnel should not uninstall electrical appliances at will, in case of electric shock or mistake. The platform should be hoisted and supported when the platform is being repaired under the platform of the platform, so as to prevent the sudden descent of the platform, causing casualties. The overflow valve should not be adjusted arbitrarily. Every element in the hydraulic system works under pressure. Any adjustment of the overflow valve may cause the hydraulic system to operate improperly. There will be unnecessary damage to people, machines and things. In any part of the hydraulic system, the pressure oil must be unloaded first, lest the pressure oil spout and the table suddenly fall. Monthly maintenance A. Roller, shaft and bearing, oil cylinder pin shaft and bearing, arm hinge shaft and bearing, etc.
Q:How to automatically lift up and lift
If I want to reach a certain time, the platform automatically drops, how to achieve? There is a time relay. Thank you very much!
Q:What is the main shaft of the horizontal milling machine
Horizontal movements of spindle of the milling machine is driven by servo motor, each after a pair of tooth belt pulley deceleration, to the longitudinal, transverse and vertical feed movement of the ball screw to achieve three direction.
Q:There are several reasons for the hydraulic cylinder oil leak on the elevator
Internal leakage 1) wear-resisting ring on the piston is badly worn, causing friction between the piston and the cylinder liner, and finally pulling the casing, piston and seal. Sealing long term failure, piston seal (mostly U, V, Y ring, etc.) aging; 3) the hydraulic oil is dirty, and a large amount of impurities enter the cylinder to seal the piston seal to the bad.
Q:Does the shear fork lift stand belong to special equipment?
In the light of the special equipment safety supervision regulations, hoisting machinery definition: refers to used for vertical lifting or vertical and horizontal moving heavy mechanical and electrical equipment, its range is rated lifting weight greater than or equal to 0.5 t lift.
Q:How does a button in the PLC control the elevating platform
To be safe, at least two buttons.I hope my answer will help you.
Q:What is the difference between elevator and elevator platform and high-altitude platform
The elevator will use the motor to reverse the deceleration and pull the cable to lift the basket. The platform, like the high-altitude operating platform, USES hydraulic oil to pressurize or unload the platform.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range