Six masts aerial working platform(lower-storage)
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Code | GTWY-16-VI | GTWY-18-VI | GTWY-20-VI | GTWY-22-VI |
Work height(m) | 18 | 20 | 22 | 24 |
Platform height(m) | 16 | 18 | 20 | 22 |
Carrying capacity(kg) | 150 | 150 | 150 | 150 |
Storage length(m) | 2.00 | 2.00 | 2.00 | 2.00 |
Storage width(m) | 1.25 | 1.25 | 1.25 | 1.25 |
Storage height(m) | 2.0 | 2.0 | 2.18 | 2.18 |
Platform length(m) | 1.85 | 1.85 | 1.85 | 1.85 |
platform width(m) | 1.00 | 1.00 | 1.00 | 1.00 |
Guardrail height(m) | 1.1 | 1.1 | 1.1 | 1.1 |
Supporting leg size(m) | 3.40x2.90 | 3.60x3.15 | 3.60x3.15 | 4.00x3.60 |
Voltage(v)ACxDC | 220/v | 220/v | 220/v | 220/v |
Electricity machine pressure(kw) | 上台1.5kw | 上台1.5kw | 上台1.5kw | 上台1.5kw |
下台3.0kw | 下台3.0kw | 下台3.0kw | 下台3.0kw | |
Up/down speed(m/s) | 0.18/0.30 | 0.18/0.30 | 0.18/0.30 | 0.18/0.30 |
Machine-weight(kg) | 1800 | 2000 | 2200 | 2400 |
Also can choose driving wheel(will charge plus) | ||||
Total machine length will be increased 0.38m,total machine weight will be increased 200kgs after match with driving wheel. |
- Q:What happens when the platform comes up and the power goes out.
- Many platforms have an emergency drop.I hope my answer will help you.
- Q:What certificate is required to operate hydraulic platform
- The operation hydraulic platform, under 500 kg, does not require a certificate, more than 500kg can use the production manufacturer's safety production license.
- Q:What should the chain's main elevator be aware of when installing the chain
- Oil cylinders and power unit system problems. Too much power or too little can cause all kinds of problems in the elevator, so choose the right power unit.
- Q:There are different kinds of milling machine and vertical lifting machine milling machine
- Start by figuring out the difference between vertical and horizontal The main shaft of vertical milling machine is perpendicular to the workbench, and the spindle of horizontal milling machine is parallel to the workbench. The knife of vertical milling machine is relatively flexible, the scope is wider. Can use vertical milling cutter, machine clip, bit etc. Milling keyway, milling plane, boring hole, etc.
- Q:The ball of the universal milling and lifting platform rolls off, how to install,
- Screw has a variety of forms, one of the most common is to use return and return two catheters, if not nut screw the screw will not drop the ball, if there is no turn the screw nut and fell out of the ball, that is to return or return pipe is broken, have to put on reload. Let me be specific. If there is no damage, then use the lithium base grease to keep the ball rolling in separate loops, and then turn the nut back in the way of the regular nut. The key is to start at the beginning, but once the ball comes out, it's going to come back again. Try it twice. (note the non-circular path (snails) don't let the ball drop!)
- Q:How do you remove the horizontal universal elevator milling cutter
- Remove the milling cutter in a horizontal milling machine, and if you hammer it with a hammer, it is easy to break the knife and not be allowed to operate. The correct way to do this is to use both hands to pull the milling cutter out of the shaft, and when it's too tight, you can use a hammer to gently tap around the milling cutter.
- Q:What happened to the rise and fall
- The first possible reason is that the voltage is too low to check the actuator potential of the motor load. The voltage fluid range allows for a plus or minus 10% of the motor to not inspect the two phases of the three-phase line of the motor and circuit motor.
- Q:How much is the 8 square meter tatami mat
- Look at the material you choose. Eight is not too small. It is estimated to be around 5,000-1w, without a lift
- Q:The design of graduation is designed for mobile shearing and hydraulic lift
- Aluminum alloy lift, lift platform aluminum, aluminum alloy lift platform, aluminum alloy elevator, shear fork lifter, cut shear fork lifts, the fork lifts, elevator guide rail type, guide rail type cargo-lifts, set of cylinder type elevator, set of cylinder type lift table, set of cylinder type elevator, fork lift platform, guide rail type lift platform, set of cylinder lifting platform, electric lift high quality manufacturer, welcome new and old customers to choose
- Q:What about the heat treatment of the lifting platform?
- The silk rods are generally used for the processing of the adjustment, and the semi-finishing process is a stabilizing stress treatment.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
Six masts aerial working platform(lower-storage)
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Hot Searches