Full Electric Walkie Scissor Aerial Work Platform(electric motor)-JCPT

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

ModelUnitJCPT0808DCJCPT1008DCJCPT1012DCJCPT1212DC
Rated capacitykg380230450320
Extend platform Rated capacitykg113
Max number of people 2
Max working heightmm8000100001000012000
Max platform heightmm60008000800010000
Overall lengthmm2480
Overall widthmm81081011501150
Over height(rail unfold)mm2210234023402470
Overall height(rail fold)mm1750188018601990
Working platform sizemm2270×8102270×8101270×11201270×1120
Platform extend sizemm900×810 900×1120
Ground clearance(stowed)mm100
Ground clearance(lifting)mm19
Wheelbasemm1870
Min turing radius(inside)mm0
Min turing radius(outside)mm2190219023302330
Drive motorV/kw24/1.5
Lift motorV/kw3/24
Drive speed(stowed)km/h4
Drive speed(lifting)km/h0.8
Raising/Falling speedsec22/3422/4030/3330/38
Battery 4×6V/210Ah
ChargerV/A24/25
Maximum gradeability%30
Max angleº2/3
TyremmФ381×127
NWkg1950210023002730

Standard Configuration
-Proportional controller
-Automatic pot hole protection system
-4x2 drive
-Emergency stop button
-Emergency descending button
-Horn
-Working chronometer
-Transport standard forklift hole
-Extended platform
-Charge protection
-Self-lock door
-Total excursion
-Tracelessness tyre
-Self-actuating brake system
-Oil pipe explosion protection system
-Fault diagnosis system
-Tilt protection
-Motor reset protect
-Buzzer
-Folded rail
-Strut bar for safe overhaul

Optional Configuration
-AC power source connected to platform
-Working lamp
-Rotary strobe light
-Overweight sensor
-Air scoop connected with platform


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Diy a small platform principle
It is possible to design screw and motor power and variable speed system according to lifting weight.
Q:How do you remove the horizontal universal elevator milling cutter
When the milling cutter is removed from the vertical milling machine, the lever nut must be released and then the end of the rod is gently tapped. ; You should not release too much, as long as you have some loose space. When you release too much, the thread connecting the rod and the milling cutter is too short, and when you tap, you slip and even drop the knife.
Q:Which is good for mobile goods elevators?
Everyone knows that a penny a points goods, jinan economic brands cargo-lifts, although is not the lowest market price, but the interior of the lift platform all electronic components is a product of the military level,
Q:The hydraulic cylinder with hydraulic platform is changed to whether the cylinder is feasible
The pressure cylinder is very close, the hydraulic cylinder is not suitable to change to the cylinder, the change is equal to make a new cylinder.
Q:The tomb raider was not able to pry the gear in order
There are four of them, four of them. See the white climbing wall outside the elevator? Find a way to burst open a hole in the iron wire and climb to the fourth gear. There was no order in this gear, four of them were done, and the elevator fell down.
Q:What happened to the rise and fall
The first possible reason is that the voltage is too low to check the actuator potential of the motor load. For users, a huge lift seems very mysterious, from which a small parts out of the question can let you helpless, Beijing force high lifting mechanical wang manager here to give you a little small pupil:
Q:There are several reasons for the hydraulic cylinder oil leak on the elevator
Internal leakage 1) wear-resisting ring on the piston is badly worn, causing friction between the piston and the cylinder liner, and finally pulling the casing, piston and seal. Sealing long term failure, piston seal (mostly U, V, Y ring, etc.) aging; 3) the hydraulic oil is dirty, and a large amount of impurities enter the cylinder to seal the piston seal to the bad.
Q:How does a button in the PLC control the elevating platform
The recommended answer is wrong, and the platform should stop at any location. You can either push the button or click the number of times to tell whether it's up or down. For example, press the ascent in one second, press two, and press the button to stop. Instructions will use timers, counters, and pulse detection. You get the idea.
Q:What is the difference between elevator and elevator platform and high-altitude platform
It's just a different call, it's a hydraulic lift.I hope my answer will help you.
Q:Who knows the price of a sloping platform?
The platform is lowest, highest, high, and how long it takes to rise. I have a few friends who do this, I can help if I need to

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range