Four-wheel drive provides srperior performance and maneuverability
Deep circulation battery, green and environmental friendly, zero emission
ABS control box and panel are firmer,lighter and water-proof.
Clear and visual operating label makes operator easy to control and avoids wrong operations.
Cable protection package, to prevent accident reduce replacing cost
Best horizontal extended distance is 7.75M.
Min turning radius, flexible
360° platform non-continuous swing
180°table swivel angle
140°(+76°/-64°) small arm luffing angle
Ground control system
Telescopic boom, step across the obstacle and work at different position when lifting at one place
On-Board diagnostics help operators troubleshoot on the fly and make adjustment in the field to maximize uptime
|Safe working load||kg||230|
|Maximum working height||m||16|
|Maximum platform height||m||14|
|Maximum horizontal extended distance||m||7.75|
|Platform swing angle||360° Non-Continuous|
|Table swivel angle||°||180°|
|Small Arm luffing angle||°||140°(+76°/-64°)|
|Dimensions||Size of working platform A×B||m||1.50x0.76|
|Complete platform length C||m||6.75|
|Complete platform width D||m||1.8|
|Complete platform height E||m||2.12|
|Lowest ground clearance G||m||0.19|
|Minimum turning radius(inner wheel)||m||1.35|
|Minimum turning radius(external wheel)||m||3.8|
|Driving speed unextended status||km/h||5|
|Driving speed under lifting and extending status||km/h||1.1|
|Maximum grade ability(4×4)||%||30%|
|Maximum allowed angle||°||3°|
|Hydraulic oil tank||L||50|
|Weight||Complete platform weight||kg||6900|
● Can Bus Technology
● Proportional controls
● Manual falling pump
● Hour meter
● Tilt protection
● Tilt alarm
● 360°non-continuous turntable rotation
● Self-leveling platform
● Fault indication on platform
● Hydraulic platform rotation
● Overheat engine protection
● Enging heater plug warm up device
● AC drive motor
● Foot pedal
● Overload limits
● Solid tyres 38×9-15
- Q:What hydraulic cylinder is used
- It is better to use hydraulic welding double acting cylinder.I hope my answer will help you.
- Q:When the hydraulic platform drops, it feels very shaken and unbalanced. Please answer?
- When you're completely down you don't have any oil pressure 【 full fall and then can't operation, full blocked ah 】 after turn off the motor Oil pressure is lifting the audience chamber pressure in gravity Driving hang on Don't let the weight of it Electricity pen again under pressure relief valve core inferior vena no pressure The cylinder is not the same as the cylinder, but the circuit is directly in the gas path
- Q:The ball of the universal milling and lifting platform rolls off, how to install,
- Screw has a variety of forms, one of the most common is to use return and return two catheters, if not nut screw the screw will not drop the ball, if there is no turn the screw nut and fell out of the ball, that is to return or return pipe is broken, have to put on reload. Let me be specific. If there is no damage, then use the lithium base grease to keep the ball rolling in separate loops, and then turn the nut back in the way of the regular nut. The key is to start at the beginning, but once the ball comes out, it's going to come back again. Try it twice. (note the non-circular path (snails) don't let the ball drop!)
- Q:Hydraulic platform repair work instruction book, trouble which big man helps to provide
- The maintenance system of elevators is maintained every month. Roller, intermediate shaft and bearing, oil cylinder pin shaft and bearing, arm hinge shaft and bearing, etc. All parts are filled with lubricating oil to extend the life of the bearing.
- Q:How to automatically lift up and lift
- The motor is controlled by a time relay, the motor is driven by a change of speed, and when it falls in place, it meets the power failure of the limit motor
- Q:What about the heat treatment of the lifting platform?
- The silk rods are generally used for the processing of the adjustment, and the semi-finishing process is a stabilizing stress treatment.
- Q:The hydraulic cylinder with hydraulic platform is changed to whether the cylinder is feasible
- Certainly not, the unit pressure difference is very big, not applicable..There must be no seal conditions.
- Q:The tomb raider was not able to pry the gear in order
- Press the switch and then descend the elevator down to the second floor and then climb to the right hand side of the cargo and pull down the first gear. Walk to the elevator and climb down the stairs to open the door between the second and third floors. Go up to the third floor and turn the elevator to the third floor. And then you go back to the second floor and you go to the third floor and you go to the sandwich and you get the second gear. Go up to the fourth floor and press the elevator up, go back to the third floor and switch to the three or four floors and twist the third gear. Come down to the entrance of the third floor elevator and then go in and use a shotgun to smash the three floors and the four floors. On the fourth floor elevator again back to the fourth floor, between the back to the fourth floor on the elevator by just open the channel on the wall opposite the detour to the fourth floor mezzanine dropped last gear lever.
- Q:Does the fixed hydraulic platform need to submit to the specification requirement
- There is no clear regulation of hydraulic lift and hydraulic platform in China, which means that you can also do it without testing. Local regulations may be different. Also, if you check, you are going to the local quality and technical supervision bureau. Should go to the special branch to register, apply for installation, after installation is finished again ask them to check the acceptance of the check. There is a fee for it. And it will be checked every year.
- Q:Seven tons of lift should be fitted with the straight screw and motor
- Force teck can offer the synchrolifting lifting system design, a full set of accessories combination: spiral elevator, commutator, drive shaft, shaft coupling, gear motor, as well as the system, a full set of CAD drawings, and the scene debugging
1. Manufacturer Overview
|Annual Output Value
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
|No.of Employees in Trade Department
|No. of Production Lines
|Product Price Range