Full Electric Walkie Scissor Aerial Work Platform(hydraulic motor)-JCPT0807DC II

Ref Price:
Loading Port:
China Main Port
Payment Terms:
Min Order Qty:
Supply Capability:

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Rated capacitykg230
Extend platform Rated capacitykg113
Max number of people2
Max working heightmm7800
Max platform heightmm5800
Overall lengthmm1860
Overall length (with outrigger)mm1840
Overall widthmm760
Over height(rail unfold)mm2160
Overall height(rail fold)mm1840
Working platform sizemm1670×740
Platform extend sizemm900×740
Ground clearance(stowed)mm90
Min turing radius(inside)mm0
Min turing radius(outside)mm1640
Drive motorV/kw2/0.5
Lift motorV/kw24/3
Drive speed(stowed)km/h6
Drive speed(lifting)km/h0.8
Raising/Falling speedsec31/37


Maximum gradeability%25
Max angle2-3

Standard Configuration
-Proportional controller
-Automatic pot hole protection system
-4x2 drive
-Emergency stop button
-Emergency descending button
-Working chronometer
-Transport standard forklift hole
-Extended platform
-Charge protection
-Self-lock door
-Total excursion
-Tracelessness tyre
-Self-actuating brake system
-Oil pipe explosion protection system
-Fault diagnosis system
-Tilt protection
-Motor reset protect
-Folded rail
-Strut bar for safe overhaul

Optional Configuration
-AC power source connected to platform
-Working lamp
-Rotary strobe light
-Overweight sensor
-Air scoop connected with platform

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:When the hydraulic platform drops, it feels very shaken and unbalanced. Please answer?
Connected to the solenoid valve is the control valve core, if it is to be repaired. To change oil, you need to lift it up to the top, and then use the safety support frame or stick to support it so that you can do what you want
Q:Diy a small platform principle
If use reduction motor may speed not soon (and consider the design of lifting platform under actual gravity reduction ratio), the situation of the specific need according to the design requirements, weigh the pros and cons.
Q:What can be done when the hydraulic platform is down?
You can't see your schematic diagram, theoretically do not use hydraulic lock, should balance valve, the frequent switch of hydraulic lock causes jitter and unstable. Shunt valve, speed regulating valve or pressure compensating valve is a common solution to solve synchronization problem. Synchronous diverters are expensive
Q:The characteristic of shear fork platform
The fixed platform shall be equipped with the requirements of use, and the attached devices shall be configured for any combination such as the safety protection device of the platform.
Q:Safety operation of hydraulic platform
Purpose: this procedure is used to guide operators to operate correctly and use hydraulic platform equipment. Two procedures: 1, the parts should be inspected carefully before they are work lifting platform, key check whether the screw connection is reliable, hydraulic pipe leaks, loose wires contact with and without, breakage, and so on and so forth. 2, lifting platform lift, put the leg in the four corners, four leg should be firmly supported on solid ground, dispatch work mesa to state level (visual). Turn on the power, the indicator should be on. Then start the motor, pump work, drop one or two in the air, check the parts and then start working again. When the temperature is below 10 ℃, should make the pump running 3-5 minutes, confirmation of oil pump work can be carried out. 3, homework personnel enter the platform after the guardrail doors should be closed, with bolt, tied on safety rope, the center of the load (people stand location) should be in the center position of workbench face.
Q:The single fork hydraulic lift platform
According to your description, should be three four-way solenoid valve core card death return, can wash the unwrapped solenoid valve, check valve core have any injury, if the strain suggest replace the solenoid valve, hydraulic elevating actually single stage it is best to use support valve as a control valve, the failure rate will be lower,
Q:What is the size of the hydraulic elevator platform for 2T
Stationary hydraulic lifting platform is to provide parameters to custom-made according to customer, not the size of the regulations, the mesa size parameters have the requirement of the clients, commonly movements itinerary, load, lift platform height, is there any need to ask me,
Q:The hydraulic platform can't rise. Why?
There's a problem with the control system, maybe that part of the circuit is in bad contact
Q:Seven tons of lift should be fitted with the straight screw and motor
A lift platform system, we are doing, you should tell your system speed, accuracy, and so on parameters, can calculate the motor power, speed, lead, lead screw diameter, guide rail, can communicate in detail
Q:What happens when the platform comes up and the power goes out.
The electromagnetic valve core can be artificially pushed back.I hope my answer will help you

1. Manufacturer Overview

Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range