|Place of Origin:|
Zhejiang, China (Mainland)
Heat Insulation, Moisture-Proof, Mould-Proof, Smoke-Proof, Waterproof
Artistic Ceilings, Honeycomb Ceilings, Integrated Ceilings, Perforated Ceilings
|Ceiling Tile Shape:|
|Ceiling Tile Type:|
9X300 FLAT OR 2 GROOVES
|Packaging Details:||10/shrink ,Shrink wrapping packege or carton package|
PVC Panel, PVC ceiling, PVC wall panel and PVC siding panel are a kind of decoration material which are mainly made of PVC resin and calcium carbonate and widely applied in indoor and outdoor decorating, bathroom ceiling and kitchen ceiling, hotel and office ceiling, outdoor and indoor wall decoration, etc. It can be very easy installed and cleaned.
· Can we make an OEM order?
o We can offer or supply goods as customers' requirements.
· How can I get some samples? Free or not?
o We can send some normal samples, absolutely free.
· How does your factory do regarding quality control?
o "Quality is priority." We always attach great importance to quality controlling from the very beginning to the very end. Our factory has gained ISO9001 , SGS authentication, CE for Europe, etc.
- Q:Finished pvc board how to install the kitchen led lights
- In the position of two keels to open less than the lamp can be tightly embedded in the hole, the wiring installation fixed
- Q:Is there a fitting, or a way, that will both convert a pipe from PVC/CVPC to copper and reduce the size?
- cpvc, copper and pex pipe have the same outside diameter. You can run the mains (hot and cold) in cpvc, use reducing couplings or tee fittings to get to 1/2 or 3/4. From there you can use sharkbite couplings to connect the cpvc to copper.
- Q:Pvc soft glass plate how to cut
- According to different thickness of the glass application of different specifications of the ruler; such as cutting 2-3mm thick glass, available 12mmXl2mm thin strip of wood ruler; cutting 4-6mm thick glass, available 4mmX 50mm wood ruler; cutting width 8- 12mm glass, the need to use 5mm X30mm wood ruler; sometimes according to the operator's habit of using ruler. The specific cutting when the use of wood or steel tape measure the size of the glass frame, and then cut on the ruler size; to consider leaving 3mm gap and 2mm knife edge. Such as cutting 2-3mm thick glass can be on the ruler of the small nail close to the side of the glass, glass knife against the other end of the ruler, one hand by holding a small nail to withstand the glass edge does not make it loose, the other hand Grasp the cutting edge straight cut, can not have the severity and bending phenomenon.
- Q:Density board and PVC which expensive
- Normal is PVC expensive, but here there are many limited conditions
There are many kinds of PVC, MDF there are many kinds, such as thickness, density and so on
High density board general prices are relatively high, and low formaldehyde content of the floor price higher, such as to reach the E0 level
So there are specific problems specific analysis
- Q:PVC floor production process
- Sports floor is divided into indoor sports flooring and outdoor sports flooring, indoor sports flooring generally professional sports wood flooring, PVC sports floor, acrylic (polyurethane) sports ground, rubber flooring and so on.
PVC sports flooring is the use of polyvinyl chloride materials specifically for the development of sports venues for a floor, specifically with polyvinyl chloride and its copolymer resin as the main raw material, adding filler, plasticizer, stabilizer, coloring agent and other accessories, On a sheet-like continuous substrate, by a coating process or by calendering, extrusion or extrusion processes. Generally laminated by multi-layer structure, generally wear-resistant layer (including UV treatment), glass fiber layer, elastic foam layer, grass-roots level. In recent years, PVC plastic sports flooring is very extensive, the Olympic Games and other international competitions are PVC plastic sports flooring, showing that the market prospects of this floor is very broad. (PVC sports floor by the multi-layer material made of pressure, the wear-resistant layer by the high concentration of polyvinyl chloride and polyurethane, the use of surface anti-skid embossing treatment, the middle of the polyvinyl chloride added to strengthen the size of the fiber Stability.)
- Q:Shop on the ground PVC plastic plate soft PVC or hard PVC?
- PVC flooring is generally divided into commercial flooring and sports flooring.
Commercial flooring is generally harder than sports floor. Commercial flooring in the hospital, shopping malls, ships, car lights with more places.
Sports flooring is generally relatively soft, usually used in a variety of venues, such as badminton courts, table tennis, basketball, tennis, volleyball and other venues. Floor flexibility is moderate. Athletes fall to the ground will not be injured. You can refer to the TST brand PVC floor.
- Q:can i replace a damaged pvc wall cladding board?
- Without inspecting the installation, it would be hard to say. However, some general pointers. Possibly you can remove the ceiling boards from the other side. Consider carefully cutting away the dented portion of the panel. You can probably cut away the entire damaged panel and squeeze in a replacement. You can offer the customer a 50% discount on the job.
- Q:how to build cat cages out of PVC pipe?
- This is a long article and no pix -- the descriptions good ...look on the net ......... ++ How to Make a Cat Cage Out of PVC Pipe ++of the be sure that you weave the seams of the enclosure wire screen on the outside of the cage -- so, kitty doesn't get snagged ... this is a good idea and the pvc pipe will not rot and should be easy to work with galvanized screen in a 1/2 inch open squares pattern will last a long time ... and plastic zip-ties are easy to work with..... ..... enjoy ... just make a diagram of what you want = lay out what is needed in the pipe and figure the screen cloth when done with the frame == a good PVC pipe cutter is worth that expense to make cutting precise and easy == daub the glue and twist the PVC into the fittings and corners --- some hardware stores have better selections of the fittings you need -- assemble PVC frame parts & fittings and then you can start cutting the frame .............
- Q:PC board, PP board, PE board, PVC board, ABS board, which is the best alternative to wood plate?
- These have an expansion rate, not suitable for use in the frame, I suggest you use the wood plastic, invariable, super strong, the price depends on your bargaining power, and the other with their own not much, so it does not matter
- Q:PVC pattern on the board is how to spray up, PVC plate printing machine manufacturers
- PVC pattern on the board is sprayed through the uv printer. Proceed as follows:
1, computer photoprint software to draw a good pattern;
2, print output software set a good white ink, ink and ink volume;
3, click to start, then the device automatically printed.
PVC board printing machine manufacturers concentrated in the Hangzhou area, if the distance from the near, you can go directly to study.
1. Manufacturer Overview
|Annual Output Value
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
|No.of Employees in Trade Department
|No. of Production Lines
|Product Price Range