Cheap Forging Steel Grinding Ball For Ball Mill In Top Quality
- Ref Price:
-
- Loading Port:
- Qingdao Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 25M.T. m.t.
- Supply Capability:
- 200000M.T./Year m.t./month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Chemical Elements of Cheap Forging Steel Grinding Ball For Ball Mill In Top Quality
C | Si | Mn | Cr | S | P |
0.50-0.65 | 0.15-0.37 | 0.6-1.2 | ≤0.25 | ≤0.04 | ≤0.04 |
0.7-0.9 | 0.45-0.75 | 0.7-1.25 | 0.11-0.4 | ≤0.04 | ≤0.04 |
Specification and Hardness of Cheap Forging Steel Grinding Ball For Ball Mill In Top Quality
Nominal diameter (mm) | Diameteical tolerance (mm) | Weight of signal forging Ball in average (g) | Number of piece of one ton forging ball in average | Surface hardness (HRC) | Impact toughness (j/cm²)) |
φ20 φ25 φ30 φ40 φ50 | +2 -1 | 32 64 110 263 513 | 31250 15625 9090 3802 1946 |
50-65 |
≥12 |
φ60 φ70 φ80 φ90 φ100 | +3 -2 | 888 1410 2104 2996 4110 | 1126 709 475 333 243 | ||
φ110 φ120 φ130 | +4 -2 | 5457 7102 9030 | 182 140 110 |
45-60 | |
φ140 φ150 | +4 -3 | 11278 13871 | 88 72 |
Application Fields of Cheap Forging Steel Grinding Ball For Ball Mill In Top Quality
1).Metal mines 2).Cement plants 3).Power station 4).Chemical industry
5).Chemical engineering
- Q: What are the casting parts used to test shrinkage holes?
- 3 fluorescent magnetic powder, this method can also be found in part.
- Q: What are the effects of stiffeners on castings, or on welded parts (for 2 tons or less), casting or weldments on stiffeners?
- 3, weight: if reinforcement in products, casting weight is generally greater than the welding parts (the internal organizational structure and mode of production determines the mechanical properties of materials, so it determines the weight of the product), considering the cost of transportation, certain priority structure.
- Q: What are the casting parts tested?
- The surface brightness, appearance, size, chemical composition, weight, material, surface defects, internal defects, seals need to be checked, leakage, etc.
- Q: the parts of the threaded hole is casting, casting the hole directly, and then tapping or casting, and then punch 10When the casting is ready, punch it again before tapping it Is the hole casting good or is it punched and tapped on the drilling machine after casting?
- If it is not directly cast hole hole, later processing, large pores may be directly cast out,
- Q: What are the casting parts processing engineering?
- Among them, special casting has metal mould casting, pressure casting, low pressure casting, lost wax casting (also known as precision casting), shell casting, lost foam casting, centrifugal casting, continuous casting, V casting, and clay casting
- Q: Which surface is coarser for cast iron or cast steel castings? Why?
- The surface of the steel is more rough, because the coating sand cast steel cast iron particles compared with graphite coating degree, the other one is to get a better air permeability and collapsibility of sand, the compaction degree is smaller than iron. Roughness mainly depends on the surface roughness on the surface of the sand.
- Q: Heat treatment process and purpose of casting parts
- Natural aging (also known as Chang Hua): lost in the open, the sun and rain, can have experienced years of wind and frost.
- Q: Can the casting part be phosphating with the phosphating solution of the pickling board?
- Like stainless steel casting, duplex stainless steel casting is phosphating, ductile iron gray iron is not required
- Q: Which master knows how the casting tolerances for malleable iron, gray iron and ductile iron should be chosen? Hurry up, thank youCan you provide a tolerance scale for castings, please?
- The tolerance of a specific size can be obtained from the tolerance grade and nominal size of the casting.
- Q: What's the cause of the choking of the casting?,
- 3. when casting the environment is humid, sand mold has not removed the moisture, when the casting, the moisture instantaneous transforms into the steam, causes the blowhole
1. Manufacturer Overview
| Location | Jiangyin City, Jiangsu Province, China |
| Year Established | 2012 |
| Annual Output Value | Above US$100 Million |
| Main Markets | South America; Oceania; Eastern Europe; Africa |
| Company Certifications | ISO9001;IS014001 Certificate |
2. Manufacturer Certificates
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period |
3. Manufacturer Capability
| a) Trade Capacity | |
| Nearest Port | Qingdao Port; Tianjin Port; Shanghai Port |
| Export Percentage | |
| No.of Employees in Trade Department | 5 - 10 People |
| Language Spoken: | English; Chinese; Spanish; Portuguese; Russian |
| b) Factory Information | |
| Factory Size: | 10,000-30,000 square meters |
| No. of Production Lines | Above 10 |
| Contract Manufacturing | Grinding Ball; Grinding Rod; Cylpeb; Grinding Media; Ball Mill Ball |
| Product Price Range | Average |
Send your message to us
Cheap Forging Steel Grinding Ball For Ball Mill In Top Quality
- Ref Price:
-
- Loading Port:
- Qingdao Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 25M.T. m.t.
- Supply Capability:
- 200000M.T./Year m.t./month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
