WQ series submersible sewage pump

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
3000 unit/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Product outline
WQ series submersible sewage pump developed in Shanghai Liancheng absorbs the advantages with the same products made abroad and at home, holds a comprehensive optimized design on its hydraulic model, mechanical structure,sealing, cooling, protection, control etc. points, features a good performance in discharging solids and in the prevention of fiber wrapping, high efficiency and energy-saving, strong reliability and, equipped with a specially developed electric control cabinet, not only the auto-control can be realized but also the motor can be made sure to work safely and reliably.Available with various types of installation to simplify the pump station and save the investment.
WQ series submersible sewage pump is mainly used for the municipal works, buildings, industrial sewage and sewage treatment to discharge the sewage, waste water and rainwater containing solids and long fibers.
Characteristic and advantage
1. Most of the impellers with the pump of an aperture below 400 come as a bi-runner impeller and few of them is a multi-blade centrifugal impeller. While most of the impellers with the pump of an aperture 400 and above come as a mixed flow impeller and few of them is a bi-runner impeller. The spacious pump casing runner lets the solids easily passing and the fibers uneasily wrapping so that it is most suitable for discharging sewage and dirt.
2. Two independent single end-face mechanical seals are in-series mounted, with the installation mode as the internal installation mode, and, compared with the external installation mode, the medium is more uneasy to leak and also its sealing friction pair are easier lubricated by the oil in the oil chamber. A special spiral slot or a small seam is used to resist the solid
grains to be deposited on the mechanical seal by the pump to make sure of its stable work. The unique mechanical seal layout mode and bearing combination makes the suspension arm of the shaft short, a heavy rigidity and a small jump, more benefit for reducing the leak from the mechanical seal and extending the life of it.
3. The motor of a protective grade IPX8 works in submerged mode and holds the best cooling effect. The grade F insulation makes the winding bearable to a higher temperature and, compared with common motors, more durable.
4. The perfect combination of the special electric control cabinet, the liquid level floating-ball switch and the protective components carries out the automatic monitor and alarm for
water leak and winding overheat, the protections at shortcircuit, overload, lack-of-phase and voltage-lost cut-off, the accurately auto-controls of start, stop, alternation and minimum
submerged depth of the pump, without need of special persons for looking-after, option at will is available between the selfcoupled reducing start and electronic soft start. All of these
makes sure of safe and reliable use of the pump without any worry.
5. Both motor and hydraulic parts are directly linked together, without need of turning the shaft for centering, easily disassembled and assembled to save the time, benefit for the
site maintenance, reducing the stopped time, saving the cost of repair; simple and compact structure leaves a small volume, only simple lifting equipment is needed, as a special lifting
handler is set on the pump; less land area and the pump can be placed directly in the sewage pond, without need of a special pump house, and the therefore the construction investment
can be saved by over 40.
6. Available with five installation modes for you to choose: auto-coupled, movable hard-pipe, movable soft-pipe, fixed wet type and fixed dry type installation modes.The auto-coupled installation means the connection between the pump and the water-out pipeline is made with the water outlet pipe seat of the auto-coupling, without use of the common fasteners, and, when to separate the pump from the water outlet pipe seat, just place it down along with the guide rod and then lift it, simply enough to get free from worry and trouble and save time.
The submersible sewage pump in the fixed dry type installation not only can replace the old vertical sewage pump but also does not fear of flood submersion, so there is no need of a separate flood-proof facility, benefit for lowering the cost of construction.

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:4--6 inch deep well pump head? How much per hour out of water?.
General agricultural pump 4-6 inches of lift at about 20 meters, the economic output of water is 140-200 cubic meters per hour
Q:Multi storey residential buildings also need to set up pressurized water pump room, direct water supply can not be?
Some water pressure is not enough, and since you are multi-storey, you need to add booster pump downstairs
Q:Car water pump question?
Yes But not both sides Apply small dabs a couple of inches apart on the face of the water pump than carefully spread it out try not to get any inside the pump then place the gasket on line up holes the sealer will hold it in place
Q:water pump general question?
The water pump can go bad in other ways that means it will not leak. But it will come apart in side and will not pump water. The only way to check it is to use a pressure checker. Put a light pressure on the cooling system. As the engine runs the water pressure should build up to operation tempter. Without over hearting. If the pressure build us to fast. The temp stat is stuck closed. If their is little pressure build up there is a leak in the system. The other way is to start a cold engine and watch the water in the radiator. It should start moving thought the system when the t-stat up up. If the pump was not leaking at the gasket. The seal can go bad. The is a weep hole on the bottom as well on most water pump. It could a heater line or the a hose or steel tub that cool the throbbed or a intake gasket. It could be a head gasket as well. Since you didn't give the make and model. It is hard to pin point the leak to one area.
Q:How to select the pump model?
Your vertical height is approximately equal to 190 meters, the actual line loss should be considered to be more than 200 ~ ~!How much do you need for traffic?Choose a suitable submersible deep well pump according to the flow rate! You can communicate in private!
Q:1999 toyota sienna LE water pump?
When you change the timing belt you as well change the water pump as well. If you take it to anyone for timing belt change they will ask you if you want to change water pump because its convenient to change it out at that time. But if you dont have any knowledge how to work with the timing dont mess with it take it to someone who is knows what there doing because paying couple hundred dollars is better then paying thousands for engine rebuild or new engine.
Q:2004 Chevy Trailblazer water pump?
Takes a special tool,you can pick one up at Autozone or Checkers for under 50 bucks, or just pull the water pump with the fan still attached and take it in for them to replace it for a small fee when you buy the water pump.
Q:how do i replace a water pump in an 86 jeep cherokee?
hello ok... you have some issues to ascertain... a million, be certain you placed the theromstat interior the final way. 2, examine each and all of the hoses... you have got one thats kinked or collapsed. ( normally the single close to the backside of the radiator. 3, replace the radiator cap. the actual one on the radiator. it must be venting each and all of the time subsequently no longer permitting the water rigidity to upward push while the engine is working. confident the gadget is presureised via the rigidity of the water pump..... 4, you have got a sludge blockage interior the radiator its self. Take the hose off the backside, permit each and all of the fluid run out. placed hose in perfect of radiator and only flush.... 5, the reason the heater isnt working is becasue the water isnt circulating... subsequently me thinking theres a blockage incredibly once you stated no water comes out of the bleed screw. What shade is the coolant in theradiator... is it clean, is it the fairway or blue shade of coolant further. Or is it a rusty shade. additionally ... look on the oil cap.. look interior it.. is there a whitish foam. additionally examine your dipstick. Is the oil clean , or is it milky looking. If its milky then you definately've got a blown cylinder head gasket . The coolant would be going into the cylinders. and not cooling the engine. I desire you success with this and that i'm hoping its somything so undemanding as a blocked radiator.
Q:Is something wrong with my water pump?
Sounds like a leaky gasket on pump...A suggestion : Remove lower raditor hose let old coolant drain..Maybe replace thermostat.. Refill with fresh Prestone...Check water pump bolts for tightness . Replace any hoses etc... if needed
Q:2006 chevy impala water pump?
2006 Impala Water Pump

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range