PVC 90 Deg Coupling Tee NFA23
1.ITEM NO. : NFA23
2.STANDARD: NSF/ANSI 14, 61 ASTM D2466
PVC 90 Deg Coupling Tee NFA23
1.Endure chemical corrosion well,do not get rusty,have good is acid-resisting,aikali resitance and able to corrosivity.
2.Have self-extinguishing and flame resistance,will not spontaneous coumbustion,also not combustion-supporting.
3.Ageing resitance is good:can use 30-50 years between degree of 15-60.
4.Fight electricity well.
5.Wall is smooth,wall surface tension is little,impossible to fomscale deposit.
6.Quality is light.It's convenient that install moves to unload.
7.Cleaning do not influnence water quality,will not change the composition of water quality.
8.Tha water of prevention of leakage.
1.The civil architectural facility of water supply system.
2.Swimming pool,play water prowls facility project.
- Q:What are the standard drawing numbers for hydraulic couplings?
- The ends of the pipe shall be flush. The pipe should be flush in sawing grinding wheel and other tools, and burr cleaning and blowing with high pressure air before use.When installing, the coaxiality of pipe and joint body should be kept as far as possible. If the pipe deflection is too large, it will cause sealing failure.If the pre loading force is unfavorable, the inner edge of the ambassador card sleeve is just inserted into the outer wall of the pipe, and the clamping sleeve should not be deformed obviously. When the pipeline connection, and then according to the specified tightening force assembly. Phi 6-1 card sleeve tightening force is 64-1 15N, 16 MMR 259n, Phi Phi 18mm for 450n. If the sleeve is badly deformed at pre assembly, it will lose its sealing effect.
- Q:PVC can the pipe joint be butted with the joint? How do I get it?
- One is welding, the other is adhesive bonding, and the other is double headed thread connection
- Q:What about the PVC-C joint?Catgut implantation. Where are the connections of the two tubes of the casing PVC-C?!
- PVC pipe joint and butt joint, the best way is to add between the two joints of the same type of pipe, and then use special glue to connect.
- Q:The expansion type pipe joint and the sleeve type pipe joint difference, everybody looks at the picture, this is belongs to that kind of?
- Flaredfitting: flaredfitting medium: oil, water, gas and other non corrosive or corrosive medium pipe joint with steel pipe specifications and flexible pipe welding, has the characteristics of reliable connection, good sealing performance, so it is widely used in oil refining, chemical industry, light industry, textile, metallurgy, national defense, aviation, shipbuilding and other systems; also suitable for hydraulic transmission of various mechanical engineering, machine tools and other equipment pipeline.Welded pipe joints: welded pipe joint applicable medium: oil, water, gas and other non corrosive or corrosive medium. The welding type sealing pipe joint with steel pipe specifications and flexible pipe welding, has the characteristics of reliable connection, good sealing performance, so it is widely used in oil refining and chemical engineering light industry, textile, metallurgy, aviation, defense, and ship system; also suitable for hydraulic transmission of various mechanical engineering, machine tools and other equipment pipeline. When the sleeve type pipe joint production can not meet the needs, and in the case of strong corrosion, priority can be adopted.
- Q:How many bonding methods are there in the belt joint?
- 3. heat curing joint, the heat vulcanizing joint conveyor belt interface is completely closed, not susceptible to water wetting. Technology of belt vulcanizing joint is generally placed on the belt vulcanizer frame under the frame, both ends of the alignment, then put on the pressure plate, small thermal insulation board, insulation sheets, two vulcanizer installed on each side of 1-2 meters of the platform and fixed platform, the upper surface to the lower heating plate and flat surface homogeneous or slightly lower, also cannot affect the tension rod, the belt joint two on the platform began to cure. This method is a kind of joint is the best method that can guarantee the high coupling efficiency, but also very stable, joint life is long, easy to master, but the heat curing joint process is relatively complex, high requirements for personnel, cold bonding process is simple and short-term training posts.
- Q:Can the pneumatic pipe connection be carried through the water?
- The pneumatic plastic fittings do not workThe ferrule of metal can be connected
- Q:What are the specifications and models of hydraulic pipe fittings?
- The connection forms of the pipe joint include thread, welding and clamping sleeve, and the shape of the pipe joint is straight through and elbow
- Q:What do you mean by pipe fittings 3/4?
- Supplement:1 inches =25.4 mm, =8 British points, 1/2 is four points (4 British points), DN diameter 15mm, 3/4 is six points (6 points), DN20mm.
- Q:Specification for thread of gas couplings
- 1, the trachea quick change joints, referred to as pneumatic joints.2, pneumatic connectors have foreign brands and domestic brands.
- Q:PEX floor heating pipe fittings and fittings are aluminium plastic pipes?
- (four) excellent resistance to agingA. has good temperature resistance, high density PE working temperature -40~65 DEG C, cross linking PE working temperature -40~95 DEG C.B. anti-aging properties, cold brittle temperature is low, anti ultraviolet, anti-aging ability, in the absence of high heat and strong ultraviolet radiation conditions, 50 years of service life is recognized life time. After the aluminum plastic compound, enables in the withstanding pressure, the shock resistance ability to strengthen.(five) excellent health performance of aluminum-plastic composite pipe lining for the health level of the PE process without any lead such as heavy metal stabilizer, does not contain harmful ingredients and plasticizer, no mildew and microbial breeding, clean sanitation. The intermediate aluminum layer isolates oxygen and the gas permeability is 0.
With advanced technology and equipment, our company is really powerful and with strong technological development and innovation capability. With strong technical equipment . Looking into the future, our company sincerely hopes to establish long term friendly partnership with domestic and overseas customers for yielding richer harvest in return for our society as well as creating bright future.
1. Manufacturer Overview
|Annual Output Value
||US$5 Million - US$10 Million
||North America8 %
South America 10 %
Eastern Europe 1 %
Southeast Asia 15 %
Mid East5 %
Eastern Asia 5 %
Western Europe 2%
Central America 5%
Northern Europe 2 %
Southern Europe 2 %
South Asia 5 %
Domestic Market 28%
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||port of Ningbo,Port of Shanghai
||21% - 30%
|No.of Employees in Trade Department
||30,000-50,000 square meters
|No. of Production Lines
||OEM Service Offered Design Service Offered
|Product Price Range
||Low and/or Average