Detailed Product Description
Grinding Glass Spheres
new glasses for material
Round ratio above 85%
Grinding Glass Spheres
HV, Loading 100g, residence time: 12s
the average of five point: 5270Mpa
code(HV): ≥ 5000Mpa
IV. percentage of damage
1. test condition
(1)shot peening Target:Thickness:1.2mm (steel plate)
(2)air pressure of the nozzle:0.3Mpa
(3)the space between the nozzle and the Target: 200mm
(4) time of shot peening:5min
(5)the diameter of the glass beads: 250 microns
(6)Gross Weight of the tested glass beads: 1020g
(7) the weight of the damaged
glass beads after shot peening: 1.02g
2.percentage of damage of the test : 0.1%
They are mainly used for the disperser, grinding media of industries, such as coloring, paint, ink, coatings, resins, chemical engineering, with the advantages of smooth surface, even size, high hardness, good chemical stability. Thanks to the characteristics of heat-resistant, wearable, compression strength, the filling-type bead could be used to improve glass fibre reinforced plastic, rubber, and so on.
- Q:Why are pile driving boring often deflected?
- What machine? You can not speak this person, piling, Ken positioning, partial hit
- Q:Is the spiral pile driver still being dug? Is it easy to operate? How many people do you need?
- Tengzhou Five Dragon pile driver is very good, without artificial shovel, 360 degrees rotation, six minutes can hit ten meters, diameter two meters!
- Q:How did the pile of clay work after the pile driver finished?
- After the pile driver has finished the pile, the concrete is usually pumped under the concrete.Classification by load characteristicsFriction pileFriction piles - most of the load is caused by the friction of the soil around the pile, and the resistance at the end of the pile is negligible.End bearing friction pile -- the pile whose load is mainly borne by the friction force of the pile body.End bearing pileEnd bearing piles - most of the load is carried by the supporting force of the pile tip, while the resistance at the side of the pile is negligible.
- Q:120KW piling machine needs a lot of air?
- The general experience of 1 kW 2 amps, so we can use 250A open, because your motor power is relatively large, it is best to use a control box with a starter to safe operation.
- Q:18 how much money piling machine
- Depending on how large and deep you hit the pile, the price is from tens of thousands to millions. If the individual investment, you can first inspect the small pile driver.
- Q:What pile driving machine should be used for the 400*400 square pile?
- The cylinder type diesel hammer takes the cylinder as the hammer seat and directly uses the lengthened cylinder to guide the inner wall. The two guiding rods are omitted, and the plunger is a hammer head, which can move up and down in the cylinder. When piling, the pile cap at the bottom of the hammer block is pressed on the top of the pile, lifting the plunger with a hook, and then decoupling and downward impacting to compress the air enclosed in the cylinder. And fuel injection, explosion, shock, ventilation and other work processes. Diesel hammer work is on compression ignition diesel to start, it is necessary to ensure the closed gas cylinder reaches a certain compression ratio, sometimes piling in soft soil layer is often because the reaction is too small, the amount of compression is not sufficient to ignite the ignition, it needs to use the hook to lift a hammer from multiple impact, to start. The hammer seat of the diesel hammer is provided with a fuel injection pump, an oil tank, a cooling water tank and a pile cap. The movable gap between the plunger and the cylinder is sealed with an elastic plunger ring.
- Q:What are the main types of pile drivers?
- In three, diesel hammer hammer x0d is composed of a cylinder body and a plunger piston which is similar to the working principle and the single cylinder two stroke diesel engine into the cylinder combustion under high temperature and high pressure atomized diesel combustion chamber by injection pressure generated by the detonation driven hammer. Diesel hammer according to its structural form, rod and tube type. Guide rod type diesel hammer for hammer pressure in the plunger seat the pile cap, the cylinder for hammer along two guide rods. The lifting pile, the pile hanging in place pile frame in Longmen, then put the diesel hammer at the top of the pile, the hook will lift down the cylinder, and the cylinder sleeve let off hook falling into the plunger, will be closed in the steam The in cylinder air compression cylinder rocker pin until the pressure continues to fall outside the cylinder pushing hammer seat fuel pump, fuel pump will be injected into the cylinder oil mist, oil mist meet high temperature gas burning immediately above, blasting, explosive shock down make the pile sinking, to the top push the cylinder cylinder to be picked up, to fall along the guide rod, and the beginning of the second cycle. The impact of diesel hammer to hammer cylinder as the base, and directly with the lengthened cylinder wall direction, eliminating the two guide rods, the plunger is movable under the hammer in the cylinder. When the pile. The hammer seat at the lower part of the pile cap pressure at the top of the pile, lifting plunger with a hook, and then down from shock compressed in the cylinder in the closed air.
- Q:HD50 cylinder type diesel hammer, HD62 hammer, HD80 hammer, walking pile driver, crawler type pile driver
- HD50 refers to the 5 tons of diesel pile hammer; HD62 refers to the 6.2 tons of diesel pile hammer; HD80 refers to the 8.2 tons of diesel pile hammer; walking pile driver is walking pile frame supporting diesel pile hammer general "walking hammer" or "walking type diesel pile hammer" or "walking type diesel pile hammer";
- Q:How to safely operate a pile driver?
- (6) the diesel hammer hammer machine must adjust the amount of fuel supplied to control the height of the drop hammer, and must stop hammering when the second piston ring of the upper piston is seen.(7) diesel hammer pile machine, the end of the piling operation, the cylinder should be placed on the piston seat. The application of timber pile hammer pad or pin lock.(8) when the pile is driven by vibration, no one is allowed to stay in the lower part of the frame. When pulling out the vibration, it should be vertical upward and pull out at the same time.(9) the construction site of the static pile driver shall be flat and compacted, with a slope of no more than 3%, without any water accumulation, and no underground burial shall be confirmed.
- Q:What's the model of a portable anti flood pile driver? What is the depth of the pile?
- Shape size * height * width 450*350*450mm3) work parameters:Operation object: River, Hutang embankment (homogeneous soil)Pile diameter: 60 - 120mmLength: less than or equal to 3000mmPile driving speed: 500-1000mm/minIf you don't know, you can ask me again
The company has wide experience and offers a range of equipments, expertise and services to the road marking industry. The products range from road marking equipments, reflective materials, pile driver, traffic signs, traffic barrier as well as undertaking turnkey projects. Our company will be further committed to contributing to the designing, R&D, manufacturing, and providing high quality products, customer care, prompt services as well as strong technical support to both domestic and overseas customers.
1. Manufacturer Overview
||Liaoning, China (Mainland)
|Annual Output Value
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||31% - 40%
|No.of Employees in Trade Department
||5,000-10,000 square meters
|No. of Production Lines
||OEM Service Offered
|Product Price Range