Q:I need the wiring diagram for the factory radio of a 2008 ford explorer. i need to know which wires are for the back speakers so i can connect my Hi-Lo converter to it!? thanks

I'm sorry to tell you this but I have searched on several occasions for automobile wiring diagrams and have yet to find one. I don't think they post them on the web. IMO your best bet is a Chilton or Haynes manual for your vehicle. If someone does give you a good site I would be very appreciative if you would forward it to my profile.

Q:I am replacing my garbage disposal. I have black, white wires and a black/yellow wire. How do I connect this black/yellow wire. Is this a hot wire as well?

if you do not have a circuit tester then it is time to buy that $3.00 item === it is a little glow light that will be a dim light at 110volts and a brighter light at 220volts -- has two wires with metal ends and can help you with the disposal and wall sockets or other connections ... any hardware store has this tester. NOW ... we deal with the blk/yellow wire -- it is possible that it is a ground, or it is a hot wire or it could be to a GFIC [[ ground fault interrupter circuit ]] that is in the home panel -- OR -- who knows about the electrician that was the original wiring person --- most I have ever seen in wires to a disposal is two [2] wires a blk and a wht == this is a common mistake that most DIYers make .. they do not take the time to make full investigation and label wires as they take things apart .... get the tester as that is the cheapest way to solve also look at panel for the GFIC or call an electrician ,,,,,,,,, respectfully,,, XTX

Q:(For my PC)I want to have a quadrophonic speakers (4 channels), but i want to extend 2 speakers, but their wires are limited and cant extend enough to reach my rear? what should i do?is it as simple as, cut the speaker wires and extend it with a common copper wire that you mostly found on most appliance you found on your home?

It would be best to replace the short wire with new wire of the proper length! Use speaker wire, it will cost less and that's why it's made! But, what you said would work, most likely!

Q:I am in the middle of changing my thermostat and I am so lost on where the wires go! Anyone who knows anything please help.My old system was labeled and hooked up like this:White Wire (W)Red Wire (R)Blue Wire (B)Green Wire (G)Now I am looking at my new system and these are the spots that I have:(G) (RH)(RC)This has a red wire attached like a jumper wire(Y/O) (W/B) (Y1)What wires do I plug into where? Please re-post with the wire color next to where it should go.

dear, each color line on the wire, must to CHG in joint, cause the element is created by ohm to handle short circuit of fire.

Q:In that chart it has 2 sections, one is maximum amps for chassis wiring and the other is maximum amps for power transmission. What is considered chassis wiring and what is considered power transmission?

This okorder / In that chart it has 2 sections, one is maximum amps for chassis wiring and the other is maximum amps for power transmission. What is considered chassis wiring and what is considered power transmission?

Q:One wire has part of the plastic coating on the end, the other wire does not.

the lead is the wires showing. lead wire can also mean attaching a wire and feed it through a wall attach other end to the wire and pull it through. Now if you need both ends to have wire showing take a utility knife firmly place wire on block of wood and lightly cut through the caseing. thats the thick wire that en cases the other wires and peal back and then cut it off. then carefully hold blade of utility knife and wire aganst your thumb on a 45 degrees away from you and pull that will strip the plastic off the wires hope that answers your question dave

Q:how we can predict the maximum load that stainless steel cable wire can achieved?

The maker should know the load factor of all its cables. It is not easy to know without knowing the wxact formula for the steel, the number and size of wires and how it is wound. You can come up with an estimate based on past knoledge of cable and their performances. Ask the maker

Q:im installing an amp and i have no clue what to do with thw power wire.... I read to cut open my steros power wire (usually the blue) and wrap my power wire around it... I found the blue wire but there was a tag... Caution Remote output only... This is not the wire for power supply. please connect this wire to the remote for the amplifier... Does this mean i just connect this wire directly to my amp?

ok wait hold up. so the only wire that should be hooked from the amp to the headunit is your speaker wires, remote turn on wire, and your rca cables. ....What you need to do is get the power cable(usually red) run it from positive on the battery to the POS on your amp. next put your ground wire from the GND on the amp to bare metal on your cars chasis.

Q:Is high quality CAT-5 ok to wire surround sound speakers to the receiver?

Get some 16 gauge speaker wire. If you are going more than say 40 feet go with 14 gauge. DONT BUY NAME BRAND CABLE!!! It is BS. Google it and you will find scientific tests showing there is no audible diference between a 50 cent a foot wire and a 3 dollar a foot cable. As long as you use a low enough gauge wire you will not lose any sound quality. BTW if you use cat5 it will probably catch on fire so unless you hate your house don't use that.

Q:Can you swap out a 1984 Porsche 944 wiring harness with a different car's wiring harness? If which car. Thank you.

Could it be done by someone with tons of experience? Sure, but why would you? You would spend hours upon hours patching things and cross connecting. The fact that you are asking this question means you don't have an iota of mechanical or wiring experience making the point moot. So for you? No. You can not swap out the harness for some different cars wiring harness.