Vibration Isolation Machine Mount
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 100 Units unit
- Supply Capability:
- 2000 Units per Month unit/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Detailed Product Description
1.Vibration Isolation Machine Mount
2.Screw Thread:M16-M18
3.Adjustable Quantity:4/5/6
5.Bearing Capacity:1020.4-2551kg
Product Name:Vibration Isolation Machine Mount
S85 Series Adjustable Mount
Model
Type |
Specification(mm) |
Screw Thread |
Foundation Bolt Hole |
Bearing Capacity(kg) |
S83-1 |
135X70X45 |
M14 |
25 |
400 |
S83-2 |
160X80X50 |
M14 |
25 |
600 |
S83-3 |
165X80X60 |
M16 |
25 |
800 |
S83-4 |
200X100X50 |
M16 |
28 |
900 |
S83-5 |
220X100X60 |
M16 |
30 |
1000 |
S83-6 |
240X120X70 |
M18 |
33 |
1500 |
S83-7 |
260X120X70 |
M18 |
42 |
1600 |
S83-8 |
280X130X70 |
M20 |
42 |
1800 |
S83-9 |
300X150X80 |
M20 |
42 |
2000 |
S83-10 |
300X150X100 |
M24 |
45 |
3000 |
S83-11 |
350X180X100 |
M24 |
50 |
5000 |
S83-12 |
420X200X120 |
M30 |
50 |
8000 |
- Q:After losing the fluid, first close the handwheel and pull the needle, right?
- You can pull the needle first and then close, remember when you hang the water
- Q:FANUC Oi MC hand wheel failure how to solve ah? Put the MITSUBISHI M70 system is good, on the FANUC move it will not work. Reboot and just move
- JA3 socket on the cable to other FANUC machine to try, and if the cable is good, that is, the I/O board on the hand valve interface is broken.
- Q:What is the handwheel mode above the SIEMENS NC panel?
- SIEMENS CNC system panel above the wheel mode, is used to select the system into the wheel mode, with axial selection switch, switch frequency and axial magnification, then by manually rotating the handwheel makes the selected axis moves to a corresponding position.Position the shaft on the NC mechanical tool in handwheel mode. Each turn may provide 100 or 25 square wave pulses for the user on the output of the electronic handwheel. Another output of these electronic handwheel allows the control system to detect the direction of movement. These hand wheels have different pulse rates and various output stages, which can be used in all current control devicesManual stepping, trimming, interruption, insertion, etc.. The band switch is used for the selection of axial and multiplying powers, and the pulse generator is used to send out pulses, so that the system can be collected easily.The axis and direction are selected by means of an axial selector switch.Changes in frequency (X1, X10, X100, X1000) by frequency doubling switches change the speed of movement of the unit of work.When the handwheel rotates, the encoder produces a signal corresponding to the handwheel movement. Positioning the corresponding axes coordinates by numerical control system.
- Q:Electronic hand wheel broken, how to maintain?
- Is the switch changed or the pulse is out of order?
- Q:The hand wheel of an old sewing machine can not drive the needle bar and presser foot. How can it be handled?
- Is the hand screw nut in the middle of the handwheel screwed down?
- Q:The XYZ axis does not move.
- The amount is bad or how it happened before I was to change the XYZ button
- Q:I think it's probably the back line. I'm not sure if the line is the handwheel. Who can tell?Now the handwheel does not respondAlso, my unit now has a CNC display on the SHIFT should be played after the letters, characters are all wrongCan anyone explain that, please?
- 1, the handwheel signal can through the address diagnosis, different IO card address is different, such as special 0I IO module, X13 address is the address signal wheel, hand wheel, the address value will change, if not change, can check on the handwheel 5V voltage is in place, the hand wheel is directly connected to the IO module, interface JA32, the problem is not very clear, according to the SHIFT, the input will certainly be differentIf that doesn't mean, then empty the parameters and try again. This requires debugging knowledge of FANUC
- Q:In the competitor's wheel mode, when the handwheel stops feeding, the motor is noisy, sometimes noisy and sometimes noisy. What's the matter?
- The gain characteristic is not adjusted properly.
- Q:Electronic handwheel control servo driver
- You don't know the servo drive you use. Generally speaking, servo drives have pulse direction control settings and wiring methods, but before you control, you need to give drive enable signals. And then there's the ratio. How many pulses does each handwheel give you? What is the following ratio of your drive settings? It is possible that the ratio is smaller and the motor is not turning. You drive set did not make any changes, there may be a problem, the general drive analog control and pulse direction control, PWM control and PWM control software, has different control modes, the need for some settings on the drive. See the relevant sections of the drive manual.In general, there will be a set of drive loop settings, is set in the position loop and speed loop, the two is setting the command source, there are external and internal commands (software and self generating command) effective, three is to follow the proportion that the driver receives a pulse signal to drive the external. Control the operation of several motor feedback pulse distance.. If it is confirmed that several set up, usually no problem, it is possible to interference problems, but generally run roughly is no problem, but the accuracy will be affected, when debugging is also the best ground..
- Q:Fanuc vertical machining center, manual three axis moving normal. Handwheel XY moving normal,.Z axis does not move, why?
- Did you press the Z axis lock?
1. Manufacturer Overview |
|
---|---|
Location | Hebei, China |
Year Established | 2010 |
Annual Output Value | |
Main Markets | North America South America Eastern Europe Southeast Asia Africa Oceania Mid East Eastern Asia Western Europe Central America Northern Europe Southern Europe |
Company Certifications | ISO 9001:2000 |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | 1% - 10% |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | 1,000-3,000 square meters |
No. of Production Lines | Above 10 |
Contract Manufacturing | OEM Service Offered |
Product Price Range |
Send your message to us
Vibration Isolation Machine Mount
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 100 Units unit
- Supply Capability:
- 2000 Units per Month unit/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Hot Searches
Related keywords