Plastic Vacuum Forming Machinery Lunch Box
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- -
- Supply Capability:
- 10 Sets Per Month set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Specifications of Plastic Vacuum Forming Machinery Lunch Box
1.Fully automatic vacuum forming machine integrate forming and cutting off at the same time.
2.It is vacuum forming as well as press forming and synthetical forming;
3.It can be used for processing all kinds of plastic sheet;
4.It adopts PLC controller and touch screen to control the working programme;
5.It is easy to operate and features high degree of automation
Applications of Plastic Vacuum Forming Machinery Lunch Box
It can be used for processing all kinds of plastic Lunch Box.
Packaging & Delivery of Plastic Vacuum Forming Machinery Lunch Box
Packaging Detail:Plywood case, export standard package
Delivery Detail:70days
Main technical parameter
Parameter | Unit | Model(YTHY-1100II) |
Forming Area | mm2 | 1100*1100 |
Cutting off height | mm | 160 |
Production efficiency | s/die | 3-6 |
Installation Dimension | m | 19*6*3 |
Installation power | kw | 200 |
Power supply | 3 Phase 380V 50HZ | |
3 Phase 220V 60HZ |
- Q:Blister machine fault, there is power can not start
- 3. comparison method"Comparative law" is the correct feature (or voltage waveform) characteristics and fault machine (or voltage waveform) are compared, waveform or voltage which component does not match, according to the logic circuit by measuring the signal from the pole, the pursuit of the direction of the source point detection and analysis to determine the fault location.4. measurementMeasuring method, also called static measurement, is to try to pause the computer in a certain state. According to the logic diagram, the meter is used to measure the required level and to analyze and judge the fault.5. liter temperature method"Ascending temperature method" is to artificially raise the environmental temperature, to accelerate some of the high temperature parameters of the poor components "death" to find fault.6. beat methodWhen the machine is running good or bad, may be the cause of the pin component element can weld or poor contact or metal through hole resistance increases the. In this case, the available on inspection method, tapped on the circuit board with a rubber hammer, and then check more easily.
- Q:I used to see someone on the Internet to spend 300 yuan to do a plastic machine I want to do a seek expert comments, there is a picture of how we could get the plastic sheet, before the do not understand, did not want to intervene in the hope, please master to explain in detail. Thank you
- Are you talking about the acrylic press machine in the advertising industry? If it is, it is not possible. 300 yuan is impossible to do. I don't know if I'm in any other industry.
- Q:What's the difference between a cup machine and a suction machine?
- low cost mould area can be larger, but generally not convenient adjustment; with synchronous cutting, punching cutting equipment supporting products;Need to know the details can call the Qingdao Sanyi Packaging Equipment Co Ltd
- Q:Vacuum suction machine temperature in winter can be how much?
- At present by Shenzhen Pincheng electric KZSCR system module launched specifically for plastic machine hot spot temperature control, to solve the previous high cost, and directly to the hot spot temperature and temperature control, thus avoiding the outside ambient temperature on the hot spot effect. Generally can do 500 degrees or so
- Q:I opened plastic suction machine master, it has been more than 10 years, I would like to ask Zhanjiang recruitment?
- There are very few die factories in Zhanjiang. At least I've never heard of it. As to Guangzhou, Zhuhai, Zhongshan side, Trinidad and Tobago
- Q:How much does it cost to buy a blister machine?
- More than ten thousand, general fifteen, sixty thousand, new machine. Good expensive, 2289 million have, almost twelve thirty also seems. Two mobile phones are much cheaper
- Q:I have opened the German Wen Connor three-dimensional plastic suction machine, exhibition hung positive and negative press. Will there be?
- Looking for plastic furniture factory door master work, see I suggest you go to some formal recruitment website (Zhaopin, ChinaHR, 51job), the general requirements of recruitment will be reflected in the recruitment information, first determine the location, and then search related jobs. Hope to take my advice and answer, after taking good luck can find a good job as soon as possible.
- Q:Using blister machine engraving machine to produce plate furniture, the actual good?
- If it is a larger batch of furniture, engraving machine is less efficient than electronic saw.
- Q:Ambry door plank, blister machine, what brand is good?.
- You want to buy a machine? I'll take care of the name of the machine in our factory
- Q:Product drawing six cm, with the mold almost do not shape, do not use the mold on the vacuum suction can be in place, but so that the bottom of the four thin, and the sheet is also cooked, the pro master to help
- Check the travel switch at the charging line, and then lubricate the rail
1. Manufacturer Overview |
|
---|---|
Location | Zhejiang, China |
Year Established | 2003 |
Annual Output Value | Above US$ 3 Million |
Main Markets | East European, Russia, North American, Southen America, East Asia, Africa |
Company Certifications | ISO 9001:2000 |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | Shanghai PORT |
Export Percentage | 60%~70% |
No.of Employees in Trade Department | 5~6 |
Language Spoken: | English; Chinese; |
b)Factory Information | |
Factory Size: | Above 2,000 square meters |
No. of Production Lines | 3 |
Contract Manufacturing | OEM Service Offered; Design Service Offered |
Product Price Range | Average |
Send your message to us
Plastic Vacuum Forming Machinery Lunch Box
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- -
- Supply Capability:
- 10 Sets Per Month set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Hot Searches