Aluminum Diamond Plate Mud Flaps

Hot Products

Fuel Rubber hose woven layer for oil automotive OEM

Fuel Rubber hose for oil automotive OEM 1/4 inch

Rubber Braided Hose One Layer Steel Wire high pressure 1/8

Rubber Fuel Hose Cover Braid,EPA,CARB Approved 3/8 Inch

Rubber fuel hose cover braid,EPA,CARB approved

Rubber Braided Hose One Layer Steel Wire

Rubber Braided Hose One Layer Steel Wire High Pressure

Rubber fuel hose cover braid,EPA,CARB approved 3/4

Fuel Rubber hose for oil automotive OEM 1/4'

Rubber Braided Hose One Layer Steel Wire for oil

FAQ

Where does the rubber from the car come from?

Polybutadiene rubber is prepared by the solution polymerization of butadiene butadiene rubber, with excellent cold resistance, abrasion resistance and elastic rubber tires, but also has good anti-aging properties. Polybutadiene rubber is mostly used in the production of tires, a small part for manufacturing cold products, cushioning materials and belt and rubber shoes. Butadiene rubber drawback is the poor tear resistance, wet skid resistance is not good.

The new bicycle tires are why side rubber thorns?

To have a better understanding of the tyres, you must start with tread patterns. Because the tread pattern (that is, the shape of the surface of the tyre) is the most complex and important of the four elements of the tyre design. It not only determines the characteristics of the tyres, but also determines the grip, drainage, and noise of the tyres. We can even see what kind of effect the tire is by using the shape of the tire surface or the shape of the glue block. For example: if the rubber tread is large, then this should focus on tire grip; if the rubber block is smaller and more and more channels, should be focused on drainage; if in the midline rubber block pattern appropriate dislocation, can help reduce noise.

Can the waterproof sealing strip for sunroof glass be changed?

Pay attention to the aging and deformation of the slide rail.Skylights used for a long time, in its slide, gap, usually there will be a lot of sand deposition, if not cleaned regularly, it will wear sunroof components.Operation 1: for electric sunroof, in the bumpy road, it is better not to open the sunroof completely, otherwise it will cause the deformation of the relative parts because of the vibration between the skylight and the slide rail, and even damage the motor.Operation 2: clean drain pipe and proper lubrication rail every two years.Should be cleaned regularly around the slide, usually in the use of 2 to 3 months, the rail with gauze stained with clean water cleaning, and after wiping clean, apply a little oil or butter on it.Operation 3: when the vehicle is ready for long-term parking, it is necessary to thoroughly clean the skylight track with talcum powder, so as to avoid the long time and cause the chemical reaction of the sealing ring in the air to cause the ageing.

Want to know how the rubber skid on the bus handle is set up?

This is called a heat shrinkable sheath, flame retardant, insulation, temperature resistance, heat shrinkable sleeve is a special polyolefin material, heat shrinkable sleeve, also known as EVA material.

Please help to understand what parts of the car are used rubber parts, must be more specific Oh!

There are many pieces of rubberThe place where the car fits, similar to the combination bolt,,There are contact places, similar to the floor, shock absorption faster..And where the shock is, the water tank bolts...If you want to further know the words, you can look at the car video, at a glance.

How can a soft rubber bar be machined on a lathe? The hole drilled by the drill hole is triangular

We are in the ordinary lathe on the lathe, the tool is worn by the white bar, clamping time can not be too hard, and do not extend the chuck too long. Move the drill a little slower.

Are all the rubber made from petroleum?

Natural rubber is made from plants, and then go to the processing system, a Hevea tree, these plants of Eucommia ulmoides gum, grass root; in recent years, scientists have been extracted from dandelion to natural rubber.

Colorful cars are mainly made of plastic, rubber and other materials, right?

The most essential difference lies in the plastics and rubber plastic deformation occurs in plastic deformation, while the rubber is elastic deformation. In other words, not easy to restore the original state of plastic deformation, and the rubber is relatively much easier. The elastic plastic is very small, usually less than 100%, while the rubber can reach 1000% or more plastic. In the vast majority of molding forming process of finished products is finished; and the rubber molding process after the curing process is needed.